5160 steel heat treatment
Leaf-spring steel and the sword maker's friend. Outstanding toughness with honest hardness. Typical practice for AISI 5160: austenitize at 815 to 845 °C (1500 to 1555 °F), quench (oil), then temper at 190 to 480 °C (375 to 895 °F).
- Austenitize
- 815 to 845 °C
- 1500 to 1555 °F
- Temper
- 190 to 480 °C
- 375 to 895 °F
- Quench
- Oil
- Typical hardness
- 57 to 59 HRC at a 200 C temper for blades, 44 to 48 HRC at spring tempers
The chromium buys hardenability, so ordinary oil works even on thick blades. For springs temper at 370 to 480 C.
Typical published practice for guidance. Section size, prior condition, furnace accuracy and soak time all shift the right numbers. Verify against your steel supplier's datasheet before hardening anything that matters.
5160 chemical composition
| Element | Symbol | Weight % |
|---|---|---|
| Carbon | C | 0.56 to 0.64 |
| Manganese | Mn | 0.75 to 1 |
| Silicon | Si | 0.15 to 0.35 |
| Chromium | Cr | 0.7 to 0.9 |
These are the limits of the standard's chemical range. Cr spring steel. Also known as: 55Cr3 (near), 1.7176 (near), 527A60 (near).
5160 critical temperatures
| Temperature | What it means | Estimate | Equation |
|---|---|---|---|
| Ac1 | Lower critical temperature | about 734 °C (1354 °F) | Ac1 = 723 - 10.7 Mn - 16.9 Ni + 29.1 Si + 16.9 Cr + 6.38 W |
| Ac3 | Upper critical temperature | about 764 °C (1407 °F) | Ac3 = 910 - 203 sqrt(C) + 44.7 Si - 15.2 Ni + 31.5 Mo + 104 V + 13.1 W |
| Ms | Martensite start | about 249 °C (480 °F) | Ms = 539 - 423 C - 30.4 Mn - 17.7 Ni - 12.1 Cr - 7.5 Mo |
Estimates from the mid-range composition, with element amounts in weight per cent. Correlations like these scatter by about 20 to 25 °C against measurement, and real values shift with heating rate. Source: K.W. Andrews, "Empirical formulae for the calculation of some transformation temperatures", Journal of the Iron and Steel Institute, 203 (1965) 721-727.
Questions
- What temperature do you harden 5160 steel at?
- Austenitize 5160 at 815 to 845 °C (1500 to 1555 °F), then quench: oil. This is typical published practice; section size and furnace accuracy shift the right number.
- What temperature do you temper 5160 at?
- Temper 5160 at 190 to 480 °C (375 to 895 °F). Typical hardness: 57 to 59 HRC at a 200 C temper for blades, 44 to 48 HRC at spring tempers.
- What do you quench 5160 steel in?
- Oil. The chromium buys hardenability, so ordinary oil works even on thick blades. For springs temper at 370 to 480 C.
- What is 5160 steel equivalent to?
- Other designations for 5160, or for its nearest equivalent where marked "near": 55Cr3 (near), 1.7176 (near), 527A60 (near). Check the chemistry on your supplier's datasheet before treating them as the same steel.
Other alloy steels
- 4130Cr-Mo alloy steel
- 4140Cr-Mo alloy steel
- 4340Ni-Cr-Mo alloy steel
- 6150Cr-V spring steel
- 8620Case-hardening alloy steel
- 9260Si-Mn spring steel
- 9310Case-hardening alloy steel
- 52100Bearing steel
- 80CrV2Cr-V high carbon steel
- 300MUltra-high-strength steel
Sources for this grade: SAE J404 chemical ranges; Typical published practice.
Enter your own composition and get the numbers, with sources.
Heat treatment numbers for common steels, each traced to its source paper. About HeatTreat