Skip to content

1095 vs 5160 steel

1095 (High-carbon steel). The traditional razor and knife steel. Hard, keen, and demanding about its quench.

5160 (Cr spring steel). Leaf-spring steel and the sword maker's friend. Outstanding toughness with honest hardness.

How 1095 and 5160 differ

  • 1095 carries more carbon: 0.9 to 1.03% against 0.56 to 0.64% in 5160.
  • 5160 is alloyed with chromium (0.7 to 0.9%), which 1095 does not have in any real amount.
  • 5160 is austenitized hotter: 815 to 845 °C (1500 to 1555 °F) against 790 to 815 °C (1455 to 1500 °F) for 1095.
  • The quench differs. 1095: very fast oil. 5160: oil.

Side by side

1095 and 5160 compared
10955160
TypeHigh-carbon steelCr spring steel
Carbon (C), wt %0.9 to 1.030.56 to 0.64
Manganese (Mn), wt %0.3 to 0.50.75 to 1
Silicon (Si), wt %none listed0.15 to 0.35
Chromium (Cr), wt %none listed0.7 to 0.9
Austenitize790 to 815 °C (1455 to 1500 °F)815 to 845 °C (1500 to 1555 °F)
QuenchVery fast oilOil
Temper175 to 230 °C (345 to 445 °F)190 to 480 °C (375 to 895 °F)
Typical hardness58 to 62 HRC after a 190 C temper57 to 59 HRC at a 200 C temper for blades, 44 to 48 HRC at spring tempers
Ac1 (lower critical temperature)about 719 °C (1326 °F)about 734 °C (1354 °F)
Ac3 (upper critical temperature)Withheldabout 764 °C (1407 °F)
Ms (martensite start)about 119 °C (246 °F)about 249 °C (480 °F)

Ac1, Ac3 and Ms are estimates from the Andrews (1965) correlations at mid-range composition. They are withheld where a steel falls outside the low-alloy range those correlations cover, and Ac3 is withheld for steels above about 0.8% carbon. Typical published practice for guidance. Section size, prior condition, furnace accuracy and soak time all shift the right numbers. Verify against your steel supplier's datasheet before hardening anything that matters.

Heat treating each one

1095

Hypereutectoid and low in manganese, so it is shallow hardening and wants a genuinely fast oil. Keep the soak short at the low end of the range so excess carbide stays undissolved and grain stays fine. Brine hardens it deeper but cracks are a real risk.

5160

The chromium buys hardenability, so ordinary oil works even on thick blades. For springs temper at 370 to 480 C.

Questions

What is the difference between 1095 and 5160 steel?
1095 carries more carbon: 0.9 to 1.03% against 0.56 to 0.64% in 5160. 5160 is alloyed with chromium (0.7 to 0.9%), which 1095 does not have in any real amount.
Is 1095 or 5160 harder after heat treatment?
Typical hardness for 1095: 58 to 62 HRC after a 190 C temper. For 5160: 57 to 59 HRC at a 200 C temper for blades, 44 to 48 HRC at spring tempers. The result depends on the temper you choose.
Can I heat treat 1095 and 5160 the same way?
No, each has its own recipe. 1095: austenitize at 790 to 815 °C, quench in very fast oil, temper at 175 to 230 °C. 5160: austenitize at 815 to 845 °C, quench in oil, temper at 190 to 480 °C.

Heat treatment numbers for your own steel, with sources.

Heat treatment numbers for common steels, each traced to its source paper. About HeatTreat

Get HeatTreat on Google Play