1084 vs 1095 steel
1084 (High-carbon steel). The classic beginner blade steel: eutectoid carbon, wide forgiving windows, clean results in a home shop.
1095 (High-carbon steel). The traditional razor and knife steel. Hard, keen, and demanding about its quench.
How 1084 and 1095 differ
- 1095 carries more carbon: 0.9 to 1.03% against 0.8 to 0.93% in 1084.
- Both are austenitized in much the same range: 800 to 830 °C for 1084 and 790 to 815 °C for 1095.
- The quench differs. 1084: fast oil. 1095: very fast oil.
Side by side
| 1084 | 1095 | |
|---|---|---|
| Type | High-carbon steel | High-carbon steel |
| Carbon (C), wt % | 0.8 to 0.93 | 0.9 to 1.03 |
| Manganese (Mn), wt % | 0.6 to 0.9 | 0.3 to 0.5 |
| Austenitize | 800 to 830 °C (1470 to 1525 °F) | 790 to 815 °C (1455 to 1500 °F) |
| Quench | Fast oil | Very fast oil |
| Temper | 175 to 230 °C (345 to 445 °F) | 175 to 230 °C (345 to 445 °F) |
| Typical hardness | 57 to 60 HRC after a 190 to 200 C temper | 58 to 62 HRC after a 190 C temper |
| Ac1 (lower critical temperature) | about 715 °C (1319 °F) | about 719 °C (1326 °F) |
| Ac3 (upper critical temperature) | Withheld | Withheld |
| Ms (martensite start) | about 150 °C (303 °F) | about 119 °C (246 °F) |
Ac1, Ac3 and Ms are estimates from the Andrews (1965) correlations at mid-range composition. They are withheld where a steel falls outside the low-alloy range those correlations cover, and Ac3 is withheld for steels above about 0.8% carbon. Typical published practice for guidance. Section size, prior condition, furnace accuracy and soak time all shift the right numbers. Verify against your steel supplier's datasheet before hardening anything that matters.
Heat treating each one
1084
At eutectoid carbon everything transforms cleanly with no excess carbide to manage. Normalize after forging, then harden from a low soak. Pattern-welds beautifully against 15N20.
1095
Hypereutectoid and low in manganese, so it is shallow hardening and wants a genuinely fast oil. Keep the soak short at the low end of the range so excess carbide stays undissolved and grain stays fine. Brine hardens it deeper but cracks are a real risk.
Questions
- What is the difference between 1084 and 1095 steel?
- 1095 carries more carbon: 0.9 to 1.03% against 0.8 to 0.93% in 1084. Both are austenitized in much the same range: 800 to 830 °C for 1084 and 790 to 815 °C for 1095.
- Is 1084 or 1095 harder after heat treatment?
- Typical hardness for 1084: 57 to 60 HRC after a 190 to 200 C temper. For 1095: 58 to 62 HRC after a 190 C temper. The result depends on the temper you choose.
- Can I heat treat 1084 and 1095 the same way?
- No, each has its own recipe. 1084: austenitize at 800 to 830 °C, quench in fast oil, temper at 175 to 230 °C. 1095: austenitize at 790 to 815 °C, quench in very fast oil, temper at 175 to 230 °C.
Heat treatment numbers for your own steel, with sources.
Heat treatment numbers for common steels, each traced to its source paper. About HeatTreat