Skip to content

1095 vs 52100 steel

1095 (High-carbon steel). The traditional razor and knife steel. Hard, keen, and demanding about its quench.

52100 (Bearing steel). Ball-bearing steel, and one of the finest fine-edge knife steels when heat treated with care.

How 1095 and 52100 differ

  • 52100 carries more carbon: 0.98 to 1.1% against 0.9 to 1.03% in 1095.
  • 52100 is alloyed with chromium (1.3 to 1.6%), which 1095 does not have in any real amount.
  • 52100 is austenitized hotter: 840 to 860 °C (1545 to 1580 °F) against 790 to 815 °C (1455 to 1500 °F) for 1095.
  • The quench differs. 1095: very fast oil. 52100: oil.

Side by side

1095 and 52100 compared
109552100
TypeHigh-carbon steelBearing steel
Carbon (C), wt %0.9 to 1.030.98 to 1.1
Manganese (Mn), wt %0.3 to 0.50.25 to 0.45
Silicon (Si), wt %none listed0.15 to 0.35
Chromium (Cr), wt %none listed1.3 to 1.6
Austenitize790 to 815 °C (1455 to 1500 °F)840 to 860 °C (1545 to 1580 °F)
QuenchVery fast oilOil
Temper175 to 230 °C (345 to 445 °F)160 to 230 °C (320 to 445 °F)
Typical hardness58 to 62 HRC after a 190 C temper58 to 64 HRC depending on temper
Ac1 (lower critical temperature)about 719 °C (1326 °F)about 751 °C (1384 °F)
Ac3 (upper critical temperature)WithheldWithheld
Ms (martensite start)about 119 °C (246 °F)about 71 °C (160 °F)

Ac1, Ac3 and Ms are estimates from the Andrews (1965) correlations at mid-range composition. They are withheld where a steel falls outside the low-alloy range those correlations cover, and Ac3 is withheld for steels above about 0.8% carbon. Typical published practice for guidance. Section size, prior condition, furnace accuracy and soak time all shift the right numbers. Verify against your steel supplier's datasheet before hardening anything that matters.

Heat treating each one

1095

Hypereutectoid and low in manganese, so it is shallow hardening and wants a genuinely fast oil. Keep the soak short at the low end of the range so excess carbide stays undissolved and grain stays fine. Brine hardens it deeper but cracks are a real risk.

52100

Harden from the spheroidized condition with a modest soak of 10 to 20 minutes. Hypereutectoid, so the right austenitizing dissolves only part of the carbide. Cold treatment can cut retained austenite when maximum stability matters.

Questions

What is the difference between 1095 and 52100 steel?
52100 carries more carbon: 0.98 to 1.1% against 0.9 to 1.03% in 1095. 52100 is alloyed with chromium (1.3 to 1.6%), which 1095 does not have in any real amount.
Is 1095 or 52100 harder after heat treatment?
Typical hardness for 1095: 58 to 62 HRC after a 190 C temper. For 52100: 58 to 64 HRC depending on temper. The result depends on the temper you choose.
Can I heat treat 1095 and 52100 the same way?
No, each has its own recipe. 1095: austenitize at 790 to 815 °C, quench in very fast oil, temper at 175 to 230 °C. 52100: austenitize at 840 to 860 °C, quench in oil, temper at 160 to 230 °C.

Heat treatment numbers for your own steel, with sources.

Heat treatment numbers for common steels, each traced to its source paper. About HeatTreat

Get HeatTreat on Google Play