Skip to content

1095 vs W1 steel

1095 (High-carbon steel). The traditional razor and knife steel. Hard, keen, and demanding about its quench.

W1 (Water-hardening tool steel). The old-school tool steel: plain high carbon, water quenched, hard skin over a tough core.

How 1095 and W1 differ

  • W1 carries more carbon: 0.95 to 1.1% against 0.9 to 1.03% in 1095.
  • 1095 is austenitized hotter: 790 to 815 °C (1455 to 1500 °F) against 760 to 815 °C (1400 to 1500 °F) for W1.
  • The quench differs. 1095: very fast oil. W1: water or brine, interrupted for thin sections.

Side by side

1095 and W1 compared
1095W1
TypeHigh-carbon steelWater-hardening tool steel
Carbon (C), wt %0.9 to 1.030.95 to 1.1
Manganese (Mn), wt %0.3 to 0.50.25
Silicon (Si), wt %none listed0.25
Austenitize790 to 815 °C (1455 to 1500 °F)760 to 815 °C (1400 to 1500 °F)
QuenchVery fast oilWater or brine, interrupted for thin sections
Temper175 to 230 °C (345 to 445 °F)150 to 230 °C (300 to 445 °F)
Typical hardness58 to 62 HRC after a 190 C temper58 to 64 HRC at the surface
Ac1 (lower critical temperature)about 719 °C (1326 °F)about 728 °C (1342 °F)
Ac3 (upper critical temperature)WithheldWithheld
Ms (martensite start)about 119 °C (246 °F)about 98 °C (208 °F)

Ac1, Ac3 and Ms are estimates from the Andrews (1965) correlations at mid-range composition. They are withheld where a steel falls outside the low-alloy range those correlations cover, and Ac3 is withheld for steels above about 0.8% carbon. Typical published practice for guidance. Section size, prior condition, furnace accuracy and soak time all shift the right numbers. Verify against your steel supplier's datasheet before hardening anything that matters.

Heat treating each one

1095

Hypereutectoid and low in manganese, so it is shallow hardening and wants a genuinely fast oil. Keep the soak short at the low end of the range so excess carbide stays undissolved and grain stays fine. Brine hardens it deeper but cracks are a real risk.

W1

The A681 specification spans carbon classes from 0.70 to 1.50; the values shown are a common cutlery class. Very shallow hardening, which is the feature: the core stays unhardened and tough.

Questions

What is the difference between 1095 and W1 steel?
W1 carries more carbon: 0.95 to 1.1% against 0.9 to 1.03% in 1095. 1095 is austenitized hotter: 790 to 815 °C (1455 to 1500 °F) against 760 to 815 °C (1400 to 1500 °F) for W1.
Is 1095 or W1 harder after heat treatment?
Typical hardness for 1095: 58 to 62 HRC after a 190 C temper. For W1: 58 to 64 HRC at the surface. The result depends on the temper you choose.
Can I heat treat 1095 and W1 the same way?
No, each has its own recipe. 1095: austenitize at 790 to 815 °C, quench in very fast oil, temper at 175 to 230 °C. W1: austenitize at 760 to 815 °C, quench in water or brine, interrupted for thin sections, temper at 150 to 230 °C.

Heat treatment numbers for your own steel, with sources.

Heat treatment numbers for common steels, each traced to its source paper. About HeatTreat

Get HeatTreat on Google Play