A2 steel heat treatment
Air-hardening die steel: the stability of a gas quench with real wear resistance. A fine hard-use knife steel. Typical practice for A2: austenitize at 925 to 980 °C (1695 to 1795 °F), quench (still air or aluminium plates), then temper at 175 to 230 °C (345 to 445 °F).
- Austenitize
- 925 to 980 °C
- 1695 to 1795 °F
- Temper
- 175 to 230 °C
- 345 to 445 °F
- Quench
- Still air or aluminium plates
- Typical hardness
- 57 to 62 HRC
Wrap in stainless foil against decarburization, soak 20 to 45 minutes, cool in still air. Double tempering is standard practice. Distortion is low enough to harden finished parts.
Typical published practice for guidance. Section size, prior condition, furnace accuracy and soak time all shift the right numbers. Verify against your steel supplier's datasheet before hardening anything that matters.
A2 chemical composition
| Element | Symbol | Weight % |
|---|---|---|
| Carbon | C | 0.95 to 1.05 |
| Manganese | Mn | 1 max |
| Silicon | Si | 0.5 max |
| Chromium | Cr | 4.75 to 5.5 |
| Molybdenum | Mo | 0.9 to 1.4 |
| Vanadium | V | 0.15 to 0.5 |
These are the limits of the standard's chemical range. Air-hardening tool steel. Also known as: 1.2363, X100CrMoV5, SKD12.
A2 critical temperatures
| Temperature | What it means | Estimate | Equation |
|---|---|---|---|
| Ac1 | Lower critical temperature | Withheld | Ac1 = 723 - 10.7 Mn - 16.9 Ni + 29.1 Si + 16.9 Cr + 6.38 W |
| Ac3 | Upper critical temperature | Withheld | Ac3 = 910 - 203 sqrt(C) + 44.7 Si - 15.2 Ni + 31.5 Mo + 104 V + 13.1 W |
| Ms | Martensite start | Withheld | Ms = 539 - 423 C - 30.4 Mn - 17.7 Ni - 12.1 Cr - 7.5 Mo |
Chromium near 5.1% puts A2 outside the low-alloy steels these correlations were fitted to. High-chromium tool and stainless steels need measured data.
Estimates from the mid-range composition, with element amounts in weight per cent. Correlations like these scatter by about 20 to 25 °C against measurement, and real values shift with heating rate. Source: K.W. Andrews, "Empirical formulae for the calculation of some transformation temperatures", Journal of the Iron and Steel Institute, 203 (1965) 721-727.
Questions
- What temperature do you harden A2 steel at?
- Austenitize A2 at 925 to 980 °C (1695 to 1795 °F), then quench: still air or aluminium plates. This is typical published practice; section size and furnace accuracy shift the right number.
- What temperature do you temper A2 at?
- Temper A2 at 175 to 230 °C (345 to 445 °F). Typical hardness: 57 to 62 HRC.
- What do you quench A2 steel in?
- Still air or aluminium plates. Wrap in stainless foil against decarburization, soak 20 to 45 minutes, cool in still air. Double tempering is standard practice. Distortion is low enough to harden finished parts.
- What is A2 steel equivalent to?
- Other designations for A2, or for its nearest equivalent where marked "near": 1.2363, X100CrMoV5, SKD12. Check the chemistry on your supplier's datasheet before treating them as the same steel.
Other tool steels
- W1Water-hardening tool steel
- O1Oil-hardening tool steel
- D2High-carbon high-chromium tool steel
- S7Shock-resisting tool steel
- H13Hot-work tool steel
- M2High-speed steel
Sources for this grade: ASTM A681 chemical ranges; Typical published practice.
Enter your own composition and get the numbers, with sources.
Heat treatment numbers for common steels, each traced to its source paper. About HeatTreat