1075 steel heat treatment
Forgiving high-carbon steel for blades and springs, a small step milder than 1080. Typical practice for AISI 1075: austenitize at 800 to 830 °C (1470 to 1525 °F), quench (fast oil), then temper at 175 to 260 °C (345 to 500 °F).
- Austenitize
- 800 to 830 °C
- 1470 to 1525 °F
- Temper
- 175 to 260 °C
- 345 to 500 °F
- Quench
- Fast oil
- Typical hardness
- 55 to 58 HRC after a 200 C temper
Lower manganese than 1080 makes it slightly shallower hardening. A good hamon candidate in thin sections with a fast quench.
Typical published practice for guidance. Section size, prior condition, furnace accuracy and soak time all shift the right numbers. Verify against your steel supplier's datasheet before hardening anything that matters.
1075 chemical composition
| Element | Symbol | Weight % |
|---|---|---|
| Carbon | C | 0.7 to 0.8 |
| Manganese | Mn | 0.4 to 0.7 |
These are the limits of the standard's chemical range. High-carbon steel. Also known as: C75 (near), 1.1248 (near).
1075 critical temperatures
| Temperature | What it means | Estimate | Equation |
|---|---|---|---|
| Ac1 | Lower critical temperature | about 717 °C (1323 °F) | Ac1 = 723 - 10.7 Mn - 16.9 Ni + 29.1 Si + 16.9 Cr + 6.38 W |
| Ac3 | Upper critical temperature | about 734 °C (1354 °F) | Ac3 = 910 - 203 sqrt(C) + 44.7 Si - 15.2 Ni + 31.5 Mo + 104 V + 13.1 W |
| Ms | Martensite start | about 205 °C (401 °F) | Ms = 539 - 423 C - 30.4 Mn - 17.7 Ni - 12.1 Cr - 7.5 Mo |
Estimates from the mid-range composition, with element amounts in weight per cent. Correlations like these scatter by about 20 to 25 °C against measurement, and real values shift with heating rate. Source: K.W. Andrews, "Empirical formulae for the calculation of some transformation temperatures", Journal of the Iron and Steel Institute, 203 (1965) 721-727.
Questions
- What temperature do you harden 1075 steel at?
- Austenitize 1075 at 800 to 830 °C (1470 to 1525 °F), then quench: fast oil. This is typical published practice; section size and furnace accuracy shift the right number.
- What temperature do you temper 1075 at?
- Temper 1075 at 175 to 260 °C (345 to 500 °F). Typical hardness: 55 to 58 HRC after a 200 C temper.
- What do you quench 1075 steel in?
- Fast oil. Lower manganese than 1080 makes it slightly shallower hardening. A good hamon candidate in thin sections with a fast quench.
- What is 1075 steel equivalent to?
- Other designations for 1075, or for its nearest equivalent where marked "near": C75 (near), 1.1248 (near). Check the chemistry on your supplier's datasheet before treating them as the same steel.
Other carbon steels
- 1018Low-carbon steel
- 1045Medium-carbon steel
- 1060Medium-high carbon steel
- 1080High-carbon steel
- 1084High-carbon steel
- 1095High-carbon steel
- 15N20Nickel band steel
- 26C3Very high carbon steel
Sources for this grade: SAE J403 chemical ranges; Typical published practice.
Enter your own composition and get the numbers, with sources.
Heat treatment numbers for common steels, each traced to its source paper. About HeatTreat