D2 vs MagnaCut steel
D2 (High-carbon high-chromium tool steel). The blanking-die classic: huge carbide volume, high wear resistance, semi-stainless behavior.
MagnaCut (Powder-metallurgy stainless steel). The modern knife stainless designed to drop chromium carbide entirely: tough, hard, and truly rust resistant at once.
How D2 and MagnaCut differ
- D2 carries more carbon: 1.4 to 1.6% against 1.15% in MagnaCut.
- MagnaCut is alloyed with niobium (2%), which D2 does not have in any real amount.
- D2 has far more chromium: 11 to 13% against 10.7%.
- MagnaCut is austenitized hotter: 1065 to 1120 °C (1950 to 2050 °F) against 1000 to 1030 °C (1830 to 1885 °F) for D2.
- The quench differs. D2: air, plates, or vacuum gas quench. MagnaCut: aluminium plates, then cold treatment.
Side by side
| D2 | MagnaCut | |
|---|---|---|
| Type | High-carbon high-chromium tool steel | Powder-metallurgy stainless steel |
| Carbon (C), wt % | 1.4 to 1.6 | 1.15 |
| Manganese (Mn), wt % | 0.6 max | none listed |
| Silicon (Si), wt % | 0.6 max | none listed |
| Chromium (Cr), wt % | 11 to 13 | 10.7 |
| Molybdenum (Mo), wt % | 0.7 to 1.2 | 2 |
| Vanadium (V), wt % | 1.1 max | 4 |
| Niobium (Nb), wt % | none listed | 2 |
| Nitrogen (N), wt % | none listed | 0.2 |
| Austenitize | 1000 to 1030 °C (1830 to 1885 °F) | 1065 to 1120 °C (1950 to 2050 °F) |
| Quench | Air, plates, or vacuum gas quench | Aluminium plates, then cold treatment |
| Temper | 200 to 530 °C (390 to 985 °F) | 150 to 175 °C (300 to 345 °F) |
| Typical hardness | 59 to 61 HRC with a 200 C temper, 56 to 58 HRC double tempered near 520 C | 60 to 64 HRC |
| Ac1 (lower critical temperature) | Withheld | Withheld |
| Ac3 (upper critical temperature) | Withheld | Withheld |
| Ms (martensite start) | Withheld | Withheld |
Ac1, Ac3 and Ms are estimates from the Andrews (1965) correlations at mid-range composition. They are withheld where a steel falls outside the low-alloy range those correlations cover, and Ac3 is withheld for steels above about 0.8% carbon. Typical published practice for guidance. Section size, prior condition, furnace accuracy and soak time all shift the right numbers. Verify against your steel supplier's datasheet before hardening anything that matters.
Heat treating each one
D2
Foil wrap and a proper soak of 30 to 45 minutes matter at these temperatures. Tempering near 520 C trades a little hardness for secondary carbides and is the route to take before coating. Cold treatment reduces retained austenite.
MagnaCut
Cold treatment is close to mandatory at the higher austenitizing temperatures. The designer's published datasheet recommends keeping tempers at or below about 370 C to preserve corrosion resistance.
Questions
- What is the difference between D2 and MagnaCut steel?
- D2 carries more carbon: 1.4 to 1.6% against 1.15% in MagnaCut. MagnaCut is alloyed with niobium (2%), which D2 does not have in any real amount.
- Is D2 or MagnaCut harder after heat treatment?
- Typical hardness for D2: 59 to 61 HRC with a 200 C temper, 56 to 58 HRC double tempered near 520 C. For MagnaCut: 60 to 64 HRC. The result depends on the temper you choose.
- Can I heat treat D2 and MagnaCut the same way?
- No, each has its own recipe. D2: austenitize at 1000 to 1030 °C, quench in air, plates, or vacuum gas quench, temper at 200 to 530 °C. MagnaCut: austenitize at 1065 to 1120 °C, quench in aluminium plates, then cold treatment, temper at 150 to 175 °C.
Heat treatment numbers for your own steel, with sources.
Heat treatment numbers for common steels, each traced to its source paper. About HeatTreat