1/4"-20 UNC tap drill size and clearance hole
To tap 1/4"-20 UNC, drill #7 (5.105 mm) for 75% thread. For a screw to pass through, drill a letter J (7.036 mm) clearance hole. 1/4"-20 UNC is a unified coarse thread (UNC) with a 6.35 mm (0.2500 in) major diameter and a 1.27 mm pitch (20 threads per inch).
- Tap drill, 75% thread
- #7
- 5.105 mm
- Clearance hole, normal fit
- letter J
- 7.036 mm
- Threads per inch
- 20
- 1.27 mm pitch
- Major diameter
- 6.35 mm
- 0.2500 in
Tap drill sizes for 1/4"-20 UNC
| Thread engagement | Drill | Diameter (mm) | Diameter (in) | Use it for |
|---|---|---|---|---|
| 75% thread | #7 | 5.105 mm | 0.2010 in | The usual choice for most materials |
| 50% thread | #1 | 5.791 mm | 0.2280 in | Hard or tough materials: easier tapping, fewer broken taps |
No #7 bit to hand? The closest standard bits to 5.105 mm are 5.1 mm (metric) and 13/64" (5.159 mm, fractional inch). A slightly larger bit cuts a shallower thread; a smaller one makes the tap work harder.
Clearance holes for 1/4" screws
| Fit | Drill | Diameter (mm) | Diameter (in) | Use it for |
|---|---|---|---|---|
| Close | letter H | 6.756 mm | 0.2660 in | Accurate location, well-aligned holes |
| Normal | letter J | 7.036 mm | 0.2770 in | General assembly |
| Loose | letter L | 7.366 mm | 0.2900 in | Several fasteners, or holes that may not line up |
1/4"-20 UNC thread dimensions
| Dimension | Value |
|---|---|
| Thread series | Unified coarse thread (UNC) |
| Major diameter | 6.35 mm (0.2500 in) |
| Pitch diameter | 5.627 mm (0.2215 in) |
| Minor diameter | 4.978 mm (0.1960 in) |
| Pitch | 1.27 mm (0.0500 in) |
| Threads per inch | 20 |
Head sizes for 1/4" screws and bolts
| Head type | Head diameter | Head height | Across flats | Drive | Standard |
|---|---|---|---|---|---|
| Socket Head Cap Screw | 9.53 mm | 6.35 mm | n/a | hex socket 3/16" | ASME B18.3 |
| Hex Head Bolt | n/a | 4.78 mm | 11.11 mm | external hex 7/16" | ASME B18.2.1 |
| Pan Head Screw | 12.5 mm | 4.45 mm | n/a | Phillips PH3 | ASME B18.6.3 |
| Flat Countersunk Head Screw | 12.88 mm | 3.94 mm | n/a | Phillips PH3 | ASME B18.6.3 (82 deg) |
Questions
- What size drill bit do I use for a 1/4"-20 UNC tap?
- Use a #7 (5.105 mm) drill for 75% thread, the usual choice. In hard or tough material, a #1 (5.791 mm) drill gives 50% thread and taps more easily.
- What is the clearance hole for a 1/4" screw?
- Drill letter J (7.036 mm) for a normal fit. Use letter H (6.756 mm) for a close fit, or letter L (7.366 mm) for a loose fit that forgives misaligned holes.
- How many threads per inch does 1/4"-20 UNC have?
- 20 threads per inch, which is a pitch of 1.27 mm. It is the coarse (UNC) thread for 1/4"; the fine thread is 1/4"-28 UNF.
- What size spanner and hex key fit a 1/4" bolt?
- A 1/4" hex head bolt takes a 7/16" spanner or socket. A 1/4" socket head cap screw takes a 3/16" hex key.
Every thread on this site, in your pocket.
Screw sizes, tap drills and clearance holes for the workshop, offline. About Nuts & Bolts