M6 × 1.0 tap drill size and clearance hole
To tap M6 × 1.0, drill 5.0 mm (0.1969 in) for 75% thread. For a screw to pass through, drill a 6.6 mm (0.2598 in) clearance hole. M6 × 1.0 is an ISO metric coarse thread with a 6.0 mm major diameter and a 1.0 mm pitch.
- Tap drill, 75% thread
- 5.0 mm
- 0.1969 in
- Clearance hole, normal fit
- 6.6 mm
- 0.2598 in
- Pitch
- 1.0 mm
- coarse pitch
- Major diameter
- 6.0 mm
- 0.2362 in
Tap drill sizes for M6 × 1.0
| Thread engagement | Drill | Diameter (in) | Use it for |
|---|---|---|---|
| 75% thread | 5.0 mm | 0.1969 in | The usual choice for most materials |
| 50% thread | 5.5 mm | 0.2165 in | Hard or tough materials: easier tapping, fewer broken taps |
No 5.0 mm bit to hand? The closest standard bits to 5.0 mm are #9 (4.978 mm, number gauge) and 13/64" (5.159 mm, fractional inch). A slightly larger bit cuts a shallower thread; a smaller one makes the tap work harder.
Clearance holes for M6 screws
| Fit | Drill | Diameter (in) | Use it for |
|---|---|---|---|
| Close | 6.4 mm | 0.2520 in | Accurate location, well-aligned holes |
| Normal | 6.6 mm | 0.2598 in | General assembly |
| Loose | 7.0 mm | 0.2756 in | Several fasteners, or holes that may not line up |
M6 × 1.0 thread dimensions
| Dimension | Value |
|---|---|
| Thread series | ISO metric coarse thread |
| Major diameter | 6.0 mm |
| Pitch diameter | 5.35 mm |
| Minor diameter | 4.773 mm |
| Pitch | 1.0 mm |
| M6 set screw hex key | 3.0 mm |
Head sizes for M6 screws and bolts
| Head type | Head diameter | Head height | Across flats | Drive | Standard |
|---|---|---|---|---|---|
| Socket Head Cap Screw | 10.0 mm | 6.0 mm | n/a | hex socket 5.0 | DIN 912, ISO 4762 |
| Hex Head Bolt | n/a | 4.0 mm | 10.0 mm | external hex 10 | DIN 933, ISO 4017 (full thread), DIN 931, ISO 4014 (partial thread) |
| Pan Head Screw | 12.0 mm | 4.6 mm | n/a | Phillips PH3 | DIN 7985, ISO 7045 |
| Flat Countersunk Head Screw | 11.0 mm | 3.0 mm | n/a | Phillips PH3 | DIN 965, ISO 7046 (90 deg) |
Questions
- What size drill bit do I use for an M6 × 1.0 tap?
- Use a 5.0 mm (0.1969 in) drill for 75% thread, the usual choice. In hard or tough material, a 5.5 mm (0.2165 in) drill gives 50% thread and taps more easily.
- What is the clearance hole for an M6 screw?
- Drill 6.6 mm (0.2598 in) for a normal fit. Use 6.4 mm (0.2520 in) for a close fit, or 7.0 mm (0.2756 in) for a loose fit that forgives misaligned holes.
- What is the pitch of M6 × 1.0?
- M6 × 1.0 has a 1.0 mm pitch, measured from one thread crest to the next. It is the coarse pitch for M6; the fine pitch is M6 × 0.75.
- What size spanner and hex key fit an M6 bolt?
- An M6 hex head bolt takes a 10 mm spanner or socket. An M6 socket head cap screw takes a 5.0 mm hex key.
Every thread on this site, in your pocket.
Screw sizes, tap drills and clearance holes for the workshop, offline. About Nuts & Bolts