#12-24 UNC tap drill size and clearance hole
To tap #12-24 UNC, drill #16 (4.496 mm) for 75% thread. For a screw to pass through, drill a letter B (6.045 mm) clearance hole. #12-24 UNC is a unified coarse thread (UNC) with a 5.486 mm (0.2160 in) major diameter and a 1.058 mm pitch (24 threads per inch).
- Tap drill, 75% thread
- #16
- 4.496 mm
- Clearance hole, normal fit
- letter B
- 6.045 mm
- Threads per inch
- 24
- 1.058 mm pitch
- Major diameter
- 5.486 mm
- 0.2160 in
Tap drill sizes for #12-24 UNC
| Thread engagement | Drill | Diameter (mm) | Diameter (in) | Use it for |
|---|---|---|---|---|
| 75% thread | #16 | 4.496 mm | 0.1770 in | The usual choice for most materials |
| 50% thread | #9 | 4.978 mm | 0.1960 in | Hard or tough materials: easier tapping, fewer broken taps |
No #16 bit to hand? The closest standard bits to 4.496 mm are 4.5 mm (metric) and 11/64" (4.366 mm, fractional inch). A slightly larger bit cuts a shallower thread; a smaller one makes the tap work harder.
Clearance holes for #12 screws
| Fit | Drill | Diameter (mm) | Diameter (in) | Use it for |
|---|---|---|---|---|
| Close | #1 | 5.791 mm | 0.2280 in | Accurate location, well-aligned holes |
| Normal | letter B | 6.045 mm | 0.2380 in | General assembly |
| Loose | letter E | 6.35 mm | 0.2500 in | Several fasteners, or holes that may not line up |
#12-24 UNC thread dimensions
| Dimension | Value |
|---|---|
| Thread series | Unified coarse thread (UNC) |
| Major diameter | 5.486 mm (0.2160 in) |
| Pitch diameter | 4.798 mm (0.1889 in) |
| Minor diameter | 4.188 mm (0.1649 in) |
| Pitch | 1.058 mm (0.0417 in) |
| Threads per inch | 24 |
Head sizes for #12 screws and bolts
| Head type | Head diameter | Head height | Across flats | Drive | Standard |
|---|---|---|---|---|---|
| Socket Head Cap Screw | 9.02 mm | 5.49 mm | n/a | hex socket 5/32" | ASME B18.3 |
| Hex Head Bolt | n/a | 4.32 mm | 11.11 mm | external hex 7/16" | ASME B18.2.1 |
| Pan Head Screw | 10.8 mm | 3.76 mm | n/a | Phillips PH2 | ASME B18.6.3 |
| Flat Countersunk Head Screw | 11.18 mm | 3.43 mm | n/a | Phillips PH2 | ASME B18.6.3 (82 deg) |
Questions
- What size drill bit do I use for a #12-24 UNC tap?
- Use a #16 (4.496 mm) drill for 75% thread, the usual choice. In hard or tough material, a #9 (4.978 mm) drill gives 50% thread and taps more easily.
- What is the clearance hole for a #12 screw?
- Drill letter B (6.045 mm) for a normal fit. Use #1 (5.791 mm) for a close fit, or letter E (6.35 mm) for a loose fit that forgives misaligned holes.
- How many threads per inch does #12-24 UNC have?
- 24 threads per inch, which is a pitch of 1.058 mm. It is the coarse (UNC) thread for #12; the fine thread is #12-28 UNF.
- What size spanner and hex key fit a #12 bolt?
- A #12 hex head bolt takes a 7/16" spanner or socket. A #12 socket head cap screw takes a 5/32" hex key.
Every thread on this site, in your pocket.
Screw sizes, tap drills and clearance holes for the workshop, offline. About Nuts & Bolts