1/4"-28 UNF tap drill size and clearance hole
To tap 1/4"-28 UNF, drill #3 (5.41 mm) for 75% thread. For a screw to pass through, drill a letter J (7.036 mm) clearance hole. 1/4"-28 UNF is a unified fine thread (UNF) with a 6.35 mm (0.2500 in) major diameter and a 0.907 mm pitch (28 threads per inch).
- Tap drill, 75% thread
- #3
- 5.41 mm
- Clearance hole, normal fit
- letter J
- 7.036 mm
- Threads per inch
- 28
- 0.907 mm pitch
- Major diameter
- 6.35 mm
- 0.2500 in
Tap drill sizes for 1/4"-28 UNF
| Thread engagement | Drill | Diameter (mm) | Diameter (in) | Use it for |
|---|---|---|---|---|
| 75% thread | #3 | 5.41 mm | 0.2130 in | The usual choice for most materials |
| 50% thread | letter A | 5.944 mm | 0.2340 in | Hard or tough materials: easier tapping, fewer broken taps |
No #3 bit to hand? The closest standard bits to 5.41 mm are 5.4 mm (metric) and 7/32" (5.556 mm, fractional inch). A slightly larger bit cuts a shallower thread; a smaller one makes the tap work harder.
Clearance holes for 1/4" screws
| Fit | Drill | Diameter (mm) | Diameter (in) | Use it for |
|---|---|---|---|---|
| Close | letter H | 6.756 mm | 0.2660 in | Accurate location, well-aligned holes |
| Normal | letter J | 7.036 mm | 0.2770 in | General assembly |
| Loose | letter L | 7.366 mm | 0.2900 in | Several fasteners, or holes that may not line up |
1/4"-28 UNF thread dimensions
| Dimension | Value |
|---|---|
| Thread series | Unified fine thread (UNF) |
| Major diameter | 6.35 mm (0.2500 in) |
| Pitch diameter | 5.762 mm (0.2269 in) |
| Minor diameter | 5.237 mm (0.2062 in) |
| Pitch | 0.907 mm (0.0357 in) |
| Threads per inch | 28 |
Head sizes for 1/4" screws and bolts
| Head type | Head diameter | Head height | Across flats | Drive | Standard |
|---|---|---|---|---|---|
| Socket Head Cap Screw | 9.53 mm | 6.35 mm | n/a | hex socket 3/16" | ASME B18.3 |
| Hex Head Bolt | n/a | 4.78 mm | 11.11 mm | external hex 7/16" | ASME B18.2.1 |
| Pan Head Screw | 12.5 mm | 4.45 mm | n/a | Phillips PH3 | ASME B18.6.3 |
| Flat Countersunk Head Screw | 12.88 mm | 3.94 mm | n/a | Phillips PH3 | ASME B18.6.3 (82 deg) |
Questions
- What size drill bit do I use for a 1/4"-28 UNF tap?
- Use a #3 (5.41 mm) drill for 75% thread, the usual choice. In hard or tough material, a letter A (5.944 mm) drill gives 50% thread and taps more easily.
- What is the clearance hole for a 1/4" screw?
- Drill letter J (7.036 mm) for a normal fit. Use letter H (6.756 mm) for a close fit, or letter L (7.366 mm) for a loose fit that forgives misaligned holes.
- How many threads per inch does 1/4"-28 UNF have?
- 28 threads per inch, which is a pitch of 0.907 mm. It is the fine (UNF) thread for 1/4"; the coarse thread is 1/4"-20 UNC.
- What size spanner and hex key fit a 1/4" bolt?
- A 1/4" hex head bolt takes a 7/16" spanner or socket. A 1/4" socket head cap screw takes a 3/16" hex key.
Every thread on this site, in your pocket.
Screw sizes, tap drills and clearance holes for the workshop, offline. About Nuts & Bolts