#8-36 UNF tap drill size and clearance hole
To tap #8-36 UNF, drill #29 (3.454 mm) for 75% thread. For a screw to pass through, drill a #14 (4.623 mm) clearance hole. #8-36 UNF is a unified fine thread (UNF) with a 4.166 mm (0.1640 in) major diameter and a 0.706 mm pitch (36 threads per inch).
- Tap drill, 75% thread
- #29
- 3.454 mm
- Clearance hole, normal fit
- #14
- 4.623 mm
- Threads per inch
- 36
- 0.706 mm pitch
- Major diameter
- 4.166 mm
- 0.1640 in
Tap drill sizes for #8-36 UNF
| Thread engagement | Drill | Diameter (mm) | Diameter (in) | Use it for |
|---|---|---|---|---|
| 75% thread | #29 | 3.454 mm | 0.1360 in | The usual choice for most materials |
| 50% thread | #24 | 3.861 mm | 0.1520 in | Hard or tough materials: easier tapping, fewer broken taps |
No #29 bit to hand? The closest standard bits to 3.454 mm are 3.5 mm (metric) and 9/64" (3.572 mm, fractional inch). A slightly larger bit cuts a shallower thread; a smaller one makes the tap work harder.
Clearance holes for #8 screws
| Fit | Drill | Diameter (mm) | Diameter (in) | Use it for |
|---|---|---|---|---|
| Close | #17 | 4.394 mm | 0.1730 in | Accurate location, well-aligned holes |
| Normal | #14 | 4.623 mm | 0.1820 in | General assembly |
| Loose | #9 | 4.978 mm | 0.1960 in | Several fasteners, or holes that may not line up |
#8-36 UNF thread dimensions
| Dimension | Value |
|---|---|
| Thread series | Unified fine thread (UNF) |
| Major diameter | 4.166 mm (0.1640 in) |
| Pitch diameter | 3.72 mm (0.1465 in) |
| Minor diameter | 3.327 mm (0.1310 in) |
| Pitch | 0.706 mm (0.0278 in) |
| Threads per inch | 36 |
Head sizes for #8 screws and bolts
| Head type | Head diameter | Head height | Across flats | Drive | Standard |
|---|---|---|---|---|---|
| Socket Head Cap Screw | 6.86 mm | 4.17 mm | n/a | hex socket 9/64" | ASME B18.3 |
| Hex Head Bolt | n/a | 3.3 mm | 8.73 mm | external hex 11/32" | ASME B18.2.1 |
| Pan Head Screw | 8.18 mm | 2.92 mm | n/a | Phillips PH2 | ASME B18.6.3 |
| Flat Countersunk Head Screw | 8.43 mm | 2.82 mm | n/a | Phillips PH2 | ASME B18.6.3 (82 deg) |
Questions
- What size drill bit do I use for a #8-36 UNF tap?
- Use a #29 (3.454 mm) drill for 75% thread, the usual choice. In hard or tough material, a #24 (3.861 mm) drill gives 50% thread and taps more easily.
- What is the clearance hole for a #8 screw?
- Drill #14 (4.623 mm) for a normal fit. Use #17 (4.394 mm) for a close fit, or #9 (4.978 mm) for a loose fit that forgives misaligned holes.
- How many threads per inch does #8-36 UNF have?
- 36 threads per inch, which is a pitch of 0.706 mm. It is the fine (UNF) thread for #8; the coarse thread is #8-32 UNC.
- What size spanner and hex key fit a #8 bolt?
- A #8 hex head bolt takes a 11/32" spanner or socket. A #8 socket head cap screw takes a 9/64" hex key.
Every thread on this site, in your pocket.
Screw sizes, tap drills and clearance holes for the workshop, offline. About Nuts & Bolts