#10-32 UNF tap drill size and clearance hole
To tap #10-32 UNF, drill #21 (4.039 mm) for 75% thread. For a screw to pass through, drill a #4 (5.309 mm) clearance hole. #10-32 UNF is a unified fine thread (UNF) with a 4.826 mm (0.1900 in) major diameter and a 0.794 mm pitch (32 threads per inch).
- Tap drill, 75% thread
- #21
- 4.039 mm
- Clearance hole, normal fit
- #4
- 5.309 mm
- Threads per inch
- 32
- 0.794 mm pitch
- Major diameter
- 4.826 mm
- 0.1900 in
Tap drill sizes for #10-32 UNF
| Thread engagement | Drill | Diameter (mm) | Diameter (in) | Use it for |
|---|---|---|---|---|
| 75% thread | #21 | 4.039 mm | 0.1590 in | The usual choice for most materials |
| 50% thread | #16 | 4.496 mm | 0.1770 in | Hard or tough materials: easier tapping, fewer broken taps |
No #21 bit to hand? The closest standard bits to 4.039 mm are 4.0 mm (metric) and 5/32" (3.969 mm, fractional inch). A slightly larger bit cuts a shallower thread; a smaller one makes the tap work harder.
Clearance holes for #10 screws
| Fit | Drill | Diameter (mm) | Diameter (in) | Use it for |
|---|---|---|---|---|
| Close | #7 | 5.105 mm | 0.2010 in | Accurate location, well-aligned holes |
| Normal | #4 | 5.309 mm | 0.2090 in | General assembly |
| Loose | 7/32" | 5.556 mm | 0.2187 in | Several fasteners, or holes that may not line up |
#10-32 UNF thread dimensions
| Dimension | Value |
|---|---|
| Thread series | Unified fine thread (UNF) |
| Major diameter | 4.826 mm (0.1900 in) |
| Pitch diameter | 4.31 mm (0.1697 in) |
| Minor diameter | 3.853 mm (0.1517 in) |
| Pitch | 0.794 mm (0.0313 in) |
| Threads per inch | 32 |
Head sizes for #10 screws and bolts
| Head type | Head diameter | Head height | Across flats | Drive | Standard |
|---|---|---|---|---|---|
| Socket Head Cap Screw | 7.92 mm | 4.83 mm | n/a | hex socket 5/32" | ASME B18.3 |
| Hex Head Bolt | n/a | 3.81 mm | 9.53 mm | external hex 3/8" | ASME B18.2.1 |
| Pan Head Screw | 9.47 mm | 3.38 mm | n/a | Phillips PH2 | ASME B18.6.3 |
| Flat Countersunk Head Screw | 9.78 mm | 3.07 mm | n/a | Phillips PH2 | ASME B18.6.3 (82 deg) |
Questions
- What size drill bit do I use for a #10-32 UNF tap?
- Use a #21 (4.039 mm) drill for 75% thread, the usual choice. In hard or tough material, a #16 (4.496 mm) drill gives 50% thread and taps more easily.
- What is the clearance hole for a #10 screw?
- Drill #4 (5.309 mm) for a normal fit. Use #7 (5.105 mm) for a close fit, or 7/32" (5.556 mm) for a loose fit that forgives misaligned holes.
- How many threads per inch does #10-32 UNF have?
- 32 threads per inch, which is a pitch of 0.794 mm. It is the fine (UNF) thread for #10; the coarse thread is #10-24 UNC.
- What size spanner and hex key fit a #10 bolt?
- A #10 hex head bolt takes a 3/8" spanner or socket. A #10 socket head cap screw takes a 5/32" hex key.
Every thread on this site, in your pocket.
Screw sizes, tap drills and clearance holes for the workshop, offline. About Nuts & Bolts