#6-40 UNF tap drill size and clearance hole
To tap #6-40 UNF, drill #33 (2.87 mm) for 75% thread. For a screw to pass through, drill a #24 (3.861 mm) clearance hole. #6-40 UNF is a unified fine thread (UNF) with a 3.505 mm (0.1380 in) major diameter and a 0.635 mm pitch (40 threads per inch).
- Tap drill, 75% thread
- #33
- 2.87 mm
- Clearance hole, normal fit
- #24
- 3.861 mm
- Threads per inch
- 40
- 0.635 mm pitch
- Major diameter
- 3.505 mm
- 0.1380 in
Tap drill sizes for #6-40 UNF
| Thread engagement | Drill | Diameter (mm) | Diameter (in) | Use it for |
|---|---|---|---|---|
| 75% thread | #33 | 2.87 mm | 0.1130 in | The usual choice for most materials |
| 50% thread | #30 | 3.264 mm | 0.1285 in | Hard or tough materials: easier tapping, fewer broken taps |
No #33 bit to hand? The closest standard bits to 2.87 mm are 2.9 mm (metric) and 7/64" (2.778 mm, fractional inch). A slightly larger bit cuts a shallower thread; a smaller one makes the tap work harder.
Clearance holes for #6 screws
| Fit | Drill | Diameter (mm) | Diameter (in) | Use it for |
|---|---|---|---|---|
| Close | #27 | 3.658 mm | 0.1440 in | Accurate location, well-aligned holes |
| Normal | #24 | 3.861 mm | 0.1520 in | General assembly |
| Loose | #20 | 4.089 mm | 0.1610 in | Several fasteners, or holes that may not line up |
#6-40 UNF thread dimensions
| Dimension | Value |
|---|---|
| Thread series | Unified fine thread (UNF) |
| Major diameter | 3.505 mm (0.1380 in) |
| Pitch diameter | 3.093 mm (0.1218 in) |
| Minor diameter | 2.725 mm (0.1073 in) |
| Pitch | 0.635 mm (0.0250 in) |
| Threads per inch | 40 |
Head sizes for #6 screws and bolts
| Head type | Head diameter | Head height | Across flats | Drive | Standard |
|---|---|---|---|---|---|
| Socket Head Cap Screw | 5.74 mm | 3.51 mm | n/a | hex socket 7/64" | ASME B18.3 |
| Hex Head Bolt | n/a | 2.79 mm | 7.94 mm | external hex 5/16" | ASME B18.2.1 |
| Pan Head Screw | 6.86 mm | 2.46 mm | n/a | Phillips PH1 | ASME B18.6.3 |
| Flat Countersunk Head Screw | 7.09 mm | 2.18 mm | n/a | Phillips PH1 | ASME B18.6.3 (82 deg) |
Questions
- What size drill bit do I use for a #6-40 UNF tap?
- Use a #33 (2.87 mm) drill for 75% thread, the usual choice. In hard or tough material, a #30 (3.264 mm) drill gives 50% thread and taps more easily.
- What is the clearance hole for a #6 screw?
- Drill #24 (3.861 mm) for a normal fit. Use #27 (3.658 mm) for a close fit, or #20 (4.089 mm) for a loose fit that forgives misaligned holes.
- How many threads per inch does #6-40 UNF have?
- 40 threads per inch, which is a pitch of 0.635 mm. It is the fine (UNF) thread for #6; the coarse thread is #6-32 UNC.
- What size spanner and hex key fit a #6 bolt?
- A #6 hex head bolt takes a 5/16" spanner or socket. A #6 socket head cap screw takes a 7/64" hex key.
Every thread on this site, in your pocket.
Screw sizes, tap drills and clearance holes for the workshop, offline. About Nuts & Bolts