#4-48 UNF tap drill size and clearance hole
To tap #4-48 UNF, drill #42 (2.375 mm) for 75% thread. For a screw to pass through, drill a #30 (3.264 mm) clearance hole. #4-48 UNF is a unified fine thread (UNF) with a 2.845 mm (0.1120 in) major diameter and a 0.529 mm pitch (48 threads per inch).
- Tap drill, 75% thread
- #42
- 2.375 mm
- Clearance hole, normal fit
- #30
- 3.264 mm
- Threads per inch
- 48
- 0.529 mm pitch
- Major diameter
- 2.845 mm
- 0.1120 in
Tap drill sizes for #4-48 UNF
| Thread engagement | Drill | Diameter (mm) | Diameter (in) | Use it for |
|---|---|---|---|---|
| 75% thread | #42 | 2.375 mm | 0.0935 in | The usual choice for most materials |
| 50% thread | #38 | 2.578 mm | 0.1015 in | Hard or tough materials: easier tapping, fewer broken taps |
No #42 bit to hand? The closest standard bits to 2.375 mm are 3/32" (2.381 mm, fractional inch) and 2.4 mm (metric). A slightly larger bit cuts a shallower thread; a smaller one makes the tap work harder.
Clearance holes for #4 screws
| Fit | Drill | Diameter (mm) | Diameter (in) | Use it for |
|---|---|---|---|---|
| Close | #31 | 3.048 mm | 0.1200 in | Accurate location, well-aligned holes |
| Normal | #30 | 3.264 mm | 0.1285 in | General assembly |
| Loose | #28 | 3.569 mm | 0.1405 in | Several fasteners, or holes that may not line up |
#4-48 UNF thread dimensions
| Dimension | Value |
|---|---|
| Thread series | Unified fine thread (UNF) |
| Major diameter | 2.845 mm (0.1120 in) |
| Pitch diameter | 2.493 mm (0.0981 in) |
| Minor diameter | 2.18 mm (0.0858 in) |
| Pitch | 0.529 mm (0.0208 in) |
| Threads per inch | 48 |
Head sizes for #4 screws and bolts
| Head type | Head diameter | Head height | Across flats | Drive | Standard |
|---|---|---|---|---|---|
| Socket Head Cap Screw | 4.65 mm | 2.84 mm | n/a | hex socket 5/64" | ASME B18.3 |
| Hex Head Bolt | n/a | 2.29 mm | 6.35 mm | external hex 1/4" | ASME B18.2.1 |
| Pan Head Screw | 5.56 mm | 2.18 mm | n/a | Phillips PH1 | ASME B18.6.3 |
| Flat Countersunk Head Screw | 5.72 mm | 1.93 mm | n/a | Phillips PH1 | ASME B18.6.3 (82 deg) |
Questions
- What size drill bit do I use for a #4-48 UNF tap?
- Use a #42 (2.375 mm) drill for 75% thread, the usual choice. In hard or tough material, a #38 (2.578 mm) drill gives 50% thread and taps more easily.
- What is the clearance hole for a #4 screw?
- Drill #30 (3.264 mm) for a normal fit. Use #31 (3.048 mm) for a close fit, or #28 (3.569 mm) for a loose fit that forgives misaligned holes.
- How many threads per inch does #4-48 UNF have?
- 48 threads per inch, which is a pitch of 0.529 mm. It is the fine (UNF) thread for #4; the coarse thread is #4-40 UNC.
- What size spanner and hex key fit a #4 bolt?
- A #4 hex head bolt takes a 1/4" spanner or socket. A #4 socket head cap screw takes a 5/64" hex key.
Every thread on this site, in your pocket.
Screw sizes, tap drills and clearance holes for the workshop, offline. About Nuts & Bolts