#12-28 UNF tap drill size and clearance hole
To tap #12-28 UNF, drill #14 (4.623 mm) for 75% thread. For a screw to pass through, drill a letter B (6.045 mm) clearance hole. #12-28 UNF is a unified fine thread (UNF) with a 5.486 mm (0.2160 in) major diameter and a 0.907 mm pitch (28 threads per inch).
- Tap drill, 75% thread
- #14
- 4.623 mm
- Clearance hole, normal fit
- letter B
- 6.045 mm
- Threads per inch
- 28
- 0.907 mm pitch
- Major diameter
- 5.486 mm
- 0.2160 in
Tap drill sizes for #12-28 UNF
| Thread engagement | Drill | Diameter (mm) | Diameter (in) | Use it for |
|---|---|---|---|---|
| 75% thread | #14 | 4.623 mm | 0.1820 in | The usual choice for most materials |
| 50% thread | #8 | 5.08 mm | 0.2000 in | Hard or tough materials: easier tapping, fewer broken taps |
No #14 bit to hand? The closest standard bits to 4.623 mm are 4.6 mm (metric) and 3/16" (4.762 mm, fractional inch). A slightly larger bit cuts a shallower thread; a smaller one makes the tap work harder.
Clearance holes for #12 screws
| Fit | Drill | Diameter (mm) | Diameter (in) | Use it for |
|---|---|---|---|---|
| Close | #1 | 5.791 mm | 0.2280 in | Accurate location, well-aligned holes |
| Normal | letter B | 6.045 mm | 0.2380 in | General assembly |
| Loose | letter E | 6.35 mm | 0.2500 in | Several fasteners, or holes that may not line up |
#12-28 UNF thread dimensions
| Dimension | Value |
|---|---|
| Thread series | Unified fine thread (UNF) |
| Major diameter | 5.486 mm (0.2160 in) |
| Pitch diameter | 4.895 mm (0.1927 in) |
| Minor diameter | 4.373 mm (0.1722 in) |
| Pitch | 0.907 mm (0.0357 in) |
| Threads per inch | 28 |
Head sizes for #12 screws and bolts
| Head type | Head diameter | Head height | Across flats | Drive | Standard |
|---|---|---|---|---|---|
| Socket Head Cap Screw | 9.02 mm | 5.49 mm | n/a | hex socket 5/32" | ASME B18.3 |
| Hex Head Bolt | n/a | 4.32 mm | 11.11 mm | external hex 7/16" | ASME B18.2.1 |
| Pan Head Screw | 10.8 mm | 3.76 mm | n/a | Phillips PH2 | ASME B18.6.3 |
| Flat Countersunk Head Screw | 11.18 mm | 3.43 mm | n/a | Phillips PH2 | ASME B18.6.3 (82 deg) |
Questions
- What size drill bit do I use for a #12-28 UNF tap?
- Use a #14 (4.623 mm) drill for 75% thread, the usual choice. In hard or tough material, a #8 (5.08 mm) drill gives 50% thread and taps more easily.
- What is the clearance hole for a #12 screw?
- Drill letter B (6.045 mm) for a normal fit. Use #1 (5.791 mm) for a close fit, or letter E (6.35 mm) for a loose fit that forgives misaligned holes.
- How many threads per inch does #12-28 UNF have?
- 28 threads per inch, which is a pitch of 0.907 mm. It is the fine (UNF) thread for #12; the coarse thread is #12-24 UNC.
- What size spanner and hex key fit a #12 bolt?
- A #12 hex head bolt takes a 7/16" spanner or socket. A #12 socket head cap screw takes a 5/32" hex key.
Every thread on this site, in your pocket.
Screw sizes, tap drills and clearance holes for the workshop, offline. About Nuts & Bolts