M5 × 0.8 tap drill size and clearance hole
To tap M5 × 0.8, drill 4.2 mm (0.1654 in) for 75% thread. For a screw to pass through, drill a 5.5 mm (0.2165 in) clearance hole. M5 × 0.8 is an ISO metric coarse thread with a 5.0 mm major diameter and a 0.8 mm pitch.
- Tap drill, 75% thread
- 4.2 mm
- 0.1654 in
- Clearance hole, normal fit
- 5.5 mm
- 0.2165 in
- Pitch
- 0.8 mm
- coarse pitch
- Major diameter
- 5.0 mm
- 0.1969 in
Tap drill sizes for M5 × 0.8
| Thread engagement | Drill | Diameter (in) | Use it for |
|---|---|---|---|
| 75% thread | 4.2 mm | 0.1654 in | The usual choice for most materials |
| 50% thread | 4.6 mm | 0.1811 in | Hard or tough materials: easier tapping, fewer broken taps |
No 4.2 mm bit to hand? The closest standard bits to 4.2 mm are #19 (4.216 mm, number gauge) and 11/64" (4.366 mm, fractional inch). A slightly larger bit cuts a shallower thread; a smaller one makes the tap work harder.
Clearance holes for M5 screws
| Fit | Drill | Diameter (in) | Use it for |
|---|---|---|---|
| Close | 5.3 mm | 0.2087 in | Accurate location, well-aligned holes |
| Normal | 5.5 mm | 0.2165 in | General assembly |
| Loose | 5.8 mm | 0.2283 in | Several fasteners, or holes that may not line up |
M5 × 0.8 thread dimensions
| Dimension | Value |
|---|---|
| Thread series | ISO metric coarse thread |
| Major diameter | 5.0 mm |
| Pitch diameter | 4.48 mm |
| Minor diameter | 4.019 mm |
| Pitch | 0.8 mm |
| M5 set screw hex key | 2.5 mm |
Head sizes for M5 screws and bolts
| Head type | Head diameter | Head height | Across flats | Drive | Standard |
|---|---|---|---|---|---|
| Socket Head Cap Screw | 8.5 mm | 5.0 mm | n/a | hex socket 4.0 | DIN 912, ISO 4762 |
| Hex Head Bolt | n/a | 3.5 mm | 8.0 mm | external hex 8 | DIN 933, ISO 4017 (full thread), DIN 931, ISO 4014 (partial thread) |
| Pan Head Screw | 10.0 mm | 3.8 mm | n/a | Phillips PH2 | DIN 7985, ISO 7045 |
| Flat Countersunk Head Screw | 9.2 mm | 2.5 mm | n/a | Phillips PH2 | DIN 965, ISO 7046 (90 deg) |
Questions
- What size drill bit do I use for an M5 × 0.8 tap?
- Use a 4.2 mm (0.1654 in) drill for 75% thread, the usual choice. In hard or tough material, a 4.6 mm (0.1811 in) drill gives 50% thread and taps more easily.
- What is the clearance hole for an M5 screw?
- Drill 5.5 mm (0.2165 in) for a normal fit. Use 5.3 mm (0.2087 in) for a close fit, or 5.8 mm (0.2283 in) for a loose fit that forgives misaligned holes.
- What is the pitch of M5 × 0.8?
- M5 × 0.8 has a 0.8 mm pitch, measured from one thread crest to the next. It is the coarse pitch for M5.
- What size spanner and hex key fit an M5 bolt?
- An M5 hex head bolt takes a 8 mm spanner or socket. An M5 socket head cap screw takes a 4.0 mm hex key.
Every thread on this site, in your pocket.
Screw sizes, tap drills and clearance holes for the workshop, offline. About Nuts & Bolts