M4 × 0.7 tap drill size and clearance hole
To tap M4 × 0.7, drill 3.3 mm (0.1299 in) for 75% thread. For a screw to pass through, drill a 4.5 mm (0.1772 in) clearance hole. M4 × 0.7 is an ISO metric coarse thread with a 4.0 mm major diameter and a 0.7 mm pitch.
- Tap drill, 75% thread
- 3.3 mm
- 0.1299 in
- Clearance hole, normal fit
- 4.5 mm
- 0.1772 in
- Pitch
- 0.7 mm
- coarse pitch
- Major diameter
- 4.0 mm
- 0.1575 in
Tap drill sizes for M4 × 0.7
| Thread engagement | Drill | Diameter (in) | Use it for |
|---|---|---|---|
| 75% thread | 3.3 mm | 0.1299 in | The usual choice for most materials |
| 50% thread | 3.7 mm | 0.1437 in | Hard or tough materials: easier tapping, fewer broken taps |
No 3.3 mm bit to hand? The closest standard bits to 3.3 mm are #30 (3.264 mm, number gauge) and 1/8" (3.175 mm, fractional inch). A slightly larger bit cuts a shallower thread; a smaller one makes the tap work harder.
Clearance holes for M4 screws
| Fit | Drill | Diameter (in) | Use it for |
|---|---|---|---|
| Close | 4.3 mm | 0.1693 in | Accurate location, well-aligned holes |
| Normal | 4.5 mm | 0.1772 in | General assembly |
| Loose | 4.8 mm | 0.1890 in | Several fasteners, or holes that may not line up |
M4 × 0.7 thread dimensions
| Dimension | Value |
|---|---|
| Thread series | ISO metric coarse thread |
| Major diameter | 4.0 mm |
| Pitch diameter | 3.545 mm |
| Minor diameter | 3.141 mm |
| Pitch | 0.7 mm |
| M4 set screw hex key | 2.0 mm |
Head sizes for M4 screws and bolts
| Head type | Head diameter | Head height | Across flats | Drive | Standard |
|---|---|---|---|---|---|
| Socket Head Cap Screw | 7.0 mm | 4.0 mm | n/a | hex socket 3.0 | DIN 912, ISO 4762 |
| Hex Head Bolt | n/a | 2.8 mm | 7.0 mm | external hex 7 | DIN 933, ISO 4017 (full thread), DIN 931, ISO 4014 (partial thread) |
| Pan Head Screw | 8.0 mm | 3.1 mm | n/a | Phillips PH2 | DIN 7985, ISO 7045 |
| Flat Countersunk Head Screw | 7.5 mm | 2.2 mm | n/a | Phillips PH2 | DIN 965, ISO 7046 (90 deg) |
Questions
- What size drill bit do I use for an M4 × 0.7 tap?
- Use a 3.3 mm (0.1299 in) drill for 75% thread, the usual choice. In hard or tough material, a 3.7 mm (0.1437 in) drill gives 50% thread and taps more easily.
- What is the clearance hole for an M4 screw?
- Drill 4.5 mm (0.1772 in) for a normal fit. Use 4.3 mm (0.1693 in) for a close fit, or 4.8 mm (0.1890 in) for a loose fit that forgives misaligned holes.
- What is the pitch of M4 × 0.7?
- M4 × 0.7 has a 0.7 mm pitch, measured from one thread crest to the next. It is the coarse pitch for M4.
- What size spanner and hex key fit an M4 bolt?
- An M4 hex head bolt takes a 7 mm spanner or socket. An M4 socket head cap screw takes a 3.0 mm hex key.
Every thread on this site, in your pocket.
Screw sizes, tap drills and clearance holes for the workshop, offline. About Nuts & Bolts