M3 × 0.5 tap drill size and clearance hole
To tap M3 × 0.5, drill 2.5 mm (0.0984 in) for 75% thread. For a screw to pass through, drill a 3.4 mm (0.1339 in) clearance hole. M3 × 0.5 is an ISO metric coarse thread with a 3.0 mm major diameter and a 0.5 mm pitch.
- Tap drill, 75% thread
- 2.5 mm
- 0.0984 in
- Clearance hole, normal fit
- 3.4 mm
- 0.1339 in
- Pitch
- 0.5 mm
- coarse pitch
- Major diameter
- 3.0 mm
- 0.1181 in
Tap drill sizes for M3 × 0.5
| Thread engagement | Drill | Diameter (in) | Use it for |
|---|---|---|---|
| 75% thread | 2.5 mm | 0.0984 in | The usual choice for most materials |
| 50% thread | 2.75 mm | 0.1083 in | Hard or tough materials: easier tapping, fewer broken taps |
No 2.5 mm bit to hand? The closest standard bits to 2.5 mm are #40 (2.489 mm, number gauge) and 3/32" (2.381 mm, fractional inch). A slightly larger bit cuts a shallower thread; a smaller one makes the tap work harder.
Clearance holes for M3 screws
| Fit | Drill | Diameter (in) | Use it for |
|---|---|---|---|
| Close | 3.2 mm | 0.1260 in | Accurate location, well-aligned holes |
| Normal | 3.4 mm | 0.1339 in | General assembly |
| Loose | 3.6 mm | 0.1417 in | Several fasteners, or holes that may not line up |
M3 × 0.5 thread dimensions
| Dimension | Value |
|---|---|
| Thread series | ISO metric coarse thread |
| Major diameter | 3.0 mm |
| Pitch diameter | 2.675 mm |
| Minor diameter | 2.387 mm |
| Pitch | 0.5 mm |
| M3 set screw hex key | 1.5 mm |
Head sizes for M3 screws and bolts
| Head type | Head diameter | Head height | Across flats | Drive | Standard |
|---|---|---|---|---|---|
| Socket Head Cap Screw | 5.5 mm | 3.0 mm | n/a | hex socket 2.5 | DIN 912, ISO 4762 |
| Hex Head Bolt | n/a | 2.0 mm | 5.5 mm | external hex 5.5 | DIN 933, ISO 4017 (full thread), DIN 931, ISO 4014 (partial thread) |
| Pan Head Screw | 6.0 mm | 2.4 mm | n/a | Phillips PH1 | DIN 7985, ISO 7045 |
| Flat Countersunk Head Screw | 5.6 mm | 1.65 mm | n/a | Phillips PH1 | DIN 965, ISO 7046 (90 deg) |
Questions
- What size drill bit do I use for an M3 × 0.5 tap?
- Use a 2.5 mm (0.0984 in) drill for 75% thread, the usual choice. In hard or tough material, a 2.75 mm (0.1083 in) drill gives 50% thread and taps more easily.
- What is the clearance hole for an M3 screw?
- Drill 3.4 mm (0.1339 in) for a normal fit. Use 3.2 mm (0.1260 in) for a close fit, or 3.6 mm (0.1417 in) for a loose fit that forgives misaligned holes.
- What is the pitch of M3 × 0.5?
- M3 × 0.5 has a 0.5 mm pitch, measured from one thread crest to the next. It is the coarse pitch for M3.
- What size spanner and hex key fit an M3 bolt?
- An M3 hex head bolt takes a 5.5 mm spanner or socket. An M3 socket head cap screw takes a 2.5 mm hex key.
Every thread on this site, in your pocket.
Screw sizes, tap drills and clearance holes for the workshop, offline. About Nuts & Bolts