M24 × 3.0 tap drill size and clearance hole
To tap M24 × 3.0, drill 21.0 mm (0.8268 in) for 75% thread. For a screw to pass through, drill a 26.0 mm (1.0236 in) clearance hole. M24 × 3.0 is an ISO metric coarse thread with a 24.0 mm major diameter and a 3.0 mm pitch.
- Tap drill, 75% thread
- 21.0 mm
- 0.8268 in
- Clearance hole, normal fit
- 26.0 mm
- 1.0236 in
- Pitch
- 3.0 mm
- coarse pitch
- Major diameter
- 24.0 mm
- 0.9449 in
Tap drill sizes for M24 × 3.0
| Thread engagement | Drill | Diameter (in) | Use it for |
|---|---|---|---|
| 75% thread | 21.0 mm | 0.8268 in | The usual choice for most materials |
| 50% thread | 22.5 mm | 0.8858 in | Hard or tough materials: easier tapping, fewer broken taps |
No 21.0 mm bit to hand? The closest standard bits to 21.0 mm are 53/64" (21.034 mm, fractional inch). A slightly larger bit cuts a shallower thread; a smaller one makes the tap work harder.
Clearance holes for M24 screws
| Fit | Drill | Diameter (in) | Use it for |
|---|---|---|---|
| Close | 25.0 mm | 0.9843 in | Accurate location, well-aligned holes |
| Normal | 26.0 mm | 1.0236 in | General assembly |
| Loose | 28.0 mm | 1.1024 in | Several fasteners, or holes that may not line up |
M24 × 3.0 thread dimensions
| Dimension | Value |
|---|---|
| Thread series | ISO metric coarse thread |
| Major diameter | 24.0 mm |
| Pitch diameter | 22.051 mm |
| Minor diameter | 20.319 mm |
| Pitch | 3.0 mm |
| M24 set screw hex key | 12.0 mm |
Head sizes for M24 screws and bolts
| Head type | Head diameter | Head height | Across flats | Drive | Standard |
|---|---|---|---|---|---|
| Socket Head Cap Screw | 36.0 mm | 24.0 mm | n/a | hex socket 19.0 | DIN 912, ISO 4762 |
| Hex Head Bolt | n/a | 15.0 mm | 36.0 mm | external hex 36 | DIN 933, ISO 4017 (full thread), DIN 931, ISO 4014 (partial thread) |
Questions
- What size drill bit do I use for an M24 × 3.0 tap?
- Use a 21.0 mm (0.8268 in) drill for 75% thread, the usual choice. In hard or tough material, a 22.5 mm (0.8858 in) drill gives 50% thread and taps more easily.
- What is the clearance hole for an M24 screw?
- Drill 26.0 mm (1.0236 in) for a normal fit. Use 25.0 mm (0.9843 in) for a close fit, or 28.0 mm (1.1024 in) for a loose fit that forgives misaligned holes.
- What is the pitch of M24 × 3.0?
- M24 × 3.0 has a 3.0 mm pitch, measured from one thread crest to the next. It is the coarse pitch for M24; the fine pitch is M24 × 2.0.
- What size spanner and hex key fit an M24 bolt?
- An M24 hex head bolt takes a 36 mm spanner or socket. An M24 socket head cap screw takes a 19.0 mm hex key.
Every thread on this site, in your pocket.
Screw sizes, tap drills and clearance holes for the workshop, offline. About Nuts & Bolts