M27 × 3.0 tap drill size and clearance hole
To tap M27 × 3.0, drill 24.0 mm (0.9449 in) for 75% thread. For a screw to pass through, drill a 30.0 mm (1.1811 in) clearance hole. M27 × 3.0 is an ISO metric coarse thread with a 27.0 mm major diameter and a 3.0 mm pitch.
- Tap drill, 75% thread
- 24.0 mm
- 0.9449 in
- Clearance hole, normal fit
- 30.0 mm
- 1.1811 in
- Pitch
- 3.0 mm
- coarse pitch
- Major diameter
- 27.0 mm
- 1.0630 in
Tap drill sizes for M27 × 3.0
| Thread engagement | Drill | Diameter (in) | Use it for |
|---|---|---|---|
| 75% thread | 24.0 mm | 0.9449 in | The usual choice for most materials |
| 50% thread | 25.5 mm | 1.0039 in | Hard or tough materials: easier tapping, fewer broken taps |
No 24.0 mm bit to hand? The closest standard bits to 24.0 mm are 15/16" (23.813 mm, fractional inch). A slightly larger bit cuts a shallower thread; a smaller one makes the tap work harder.
Clearance holes for M27 screws
| Fit | Drill | Diameter (in) | Use it for |
|---|---|---|---|
| Close | 28.0 mm | 1.1024 in | Accurate location, well-aligned holes |
| Normal | 30.0 mm | 1.1811 in | General assembly |
| Loose | 32.0 mm | 1.2598 in | Several fasteners, or holes that may not line up |
M27 × 3.0 thread dimensions
| Dimension | Value |
|---|---|
| Thread series | ISO metric coarse thread |
| Major diameter | 27.0 mm |
| Pitch diameter | 25.051 mm |
| Minor diameter | 23.319 mm |
| Pitch | 3.0 mm |
Head sizes for M27 screws and bolts
| Head type | Head diameter | Head height | Across flats | Drive | Standard |
|---|---|---|---|---|---|
| Socket Head Cap Screw | 40.0 mm | 27.0 mm | n/a | hex socket 19.0 | DIN 912, ISO 4762 |
| Hex Head Bolt | n/a | 17.0 mm | 41.0 mm | external hex 41 | DIN 933, ISO 4017 (full thread), DIN 931, ISO 4014 (partial thread) |
Questions
- What size drill bit do I use for an M27 × 3.0 tap?
- Use a 24.0 mm (0.9449 in) drill for 75% thread, the usual choice. In hard or tough material, a 25.5 mm (1.0039 in) drill gives 50% thread and taps more easily.
- What is the clearance hole for an M27 screw?
- Drill 30.0 mm (1.1811 in) for a normal fit. Use 28.0 mm (1.1024 in) for a close fit, or 32.0 mm (1.2598 in) for a loose fit that forgives misaligned holes.
- What is the pitch of M27 × 3.0?
- M27 × 3.0 has a 3.0 mm pitch, measured from one thread crest to the next. It is the coarse pitch for M27; the fine pitch is M27 × 2.0.
- What size spanner and hex key fit an M27 bolt?
- An M27 hex head bolt takes a 41 mm spanner or socket. An M27 socket head cap screw takes a 19.0 mm hex key.
Every thread on this site, in your pocket.
Screw sizes, tap drills and clearance holes for the workshop, offline. About Nuts & Bolts