Skip to content

M2.5 × 0.45 tap drill size and clearance hole

To tap M2.5 × 0.45, drill 2.05 mm (0.0807 in) for 75% thread. For a screw to pass through, drill a 2.9 mm (0.1142 in) clearance hole. M2.5 × 0.45 is an ISO metric coarse thread with a 2.5 mm major diameter and a 0.45 mm pitch.

Tap drill, 75% thread
2.05 mm
0.0807 in
Clearance hole, normal fit
2.9 mm
0.1142 in
Pitch
0.45 mm
coarse pitch
Major diameter
2.5 mm
0.0984 in

Tap drill sizes for M2.5 × 0.45

Tap drill sizes for M2.5 × 0.45
Thread engagementDrillDiameter (in)Use it for
75% thread2.05 mm0.0807 inThe usual choice for most materials
50% thread2.3 mm0.0906 inHard or tough materials: easier tapping, fewer broken taps

No 2.05 mm bit to hand? The closest standard bits to 2.05 mm are #46 (2.057 mm, number gauge), 2.0 mm (metric) and 5/64" (1.984 mm, fractional inch). A slightly larger bit cuts a shallower thread; a smaller one makes the tap work harder.

Clearance holes for M2.5 screws

Clearance hole sizes for M2.5 screws
FitDrillDiameter (in)Use it for
Close2.7 mm0.1063 inAccurate location, well-aligned holes
Normal2.9 mm0.1142 inGeneral assembly
Loose3.1 mm0.1220 inSeveral fasteners, or holes that may not line up

M2.5 × 0.45 thread dimensions

M2.5 × 0.45 thread dimensions
DimensionValue
Thread seriesISO metric coarse thread
Major diameter2.5 mm
Pitch diameter2.208 mm
Minor diameter1.948 mm
Pitch0.45 mm
M2.5 set screw hex key1.3 mm

Head sizes for M2.5 screws and bolts

Head dimensions for M2.5 screws and bolts
Head typeHead diameterHead heightAcross flatsDriveStandard
Socket Head Cap Screw4.5 mm2.5 mmn/ahex socket 2.0DIN 912, ISO 4762
Hex Head Boltn/a1.7 mm5.0 mmexternal hex 5DIN 933, ISO 4017 (full thread), DIN 931, ISO 4014 (partial thread)
Pan Head Screw5.0 mm2.0 mmn/aPhillips PH1DIN 7985, ISO 7045
Flat Countersunk Head Screw4.7 mm1.5 mmn/aPhillips PH1DIN 965, ISO 7046 (90 deg)

Questions

What size drill bit do I use for an M2.5 × 0.45 tap?
Use a 2.05 mm (0.0807 in) drill for 75% thread, the usual choice. In hard or tough material, a 2.3 mm (0.0906 in) drill gives 50% thread and taps more easily.
What is the clearance hole for an M2.5 screw?
Drill 2.9 mm (0.1142 in) for a normal fit. Use 2.7 mm (0.1063 in) for a close fit, or 3.1 mm (0.1220 in) for a loose fit that forgives misaligned holes.
What is the pitch of M2.5 × 0.45?
M2.5 × 0.45 has a 0.45 mm pitch, measured from one thread crest to the next. It is the coarse pitch for M2.5.
What size spanner and hex key fit an M2.5 bolt?
An M2.5 hex head bolt takes a 5 mm spanner or socket. An M2.5 socket head cap screw takes a 2.0 mm hex key.

Every thread on this site, in your pocket.

Screw sizes, tap drills and clearance holes for the workshop, offline. About Nuts & Bolts

Get Nuts & Bolts on Google Play