M2 × 0.4 tap drill size and clearance hole
To tap M2 × 0.4, drill 1.6 mm (0.0630 in) for 75% thread. For a screw to pass through, drill a 2.4 mm (0.0945 in) clearance hole. M2 × 0.4 is an ISO metric coarse thread with a 2.0 mm major diameter and a 0.4 mm pitch.
- Tap drill, 75% thread
- 1.6 mm
- 0.0630 in
- Clearance hole, normal fit
- 2.4 mm
- 0.0945 in
- Pitch
- 0.4 mm
- coarse pitch
- Major diameter
- 2.0 mm
- 0.0787 in
Tap drill sizes for M2 × 0.4
| Thread engagement | Drill | Diameter (in) | Use it for |
|---|---|---|---|
| 75% thread | 1.6 mm | 0.0630 in | The usual choice for most materials |
| 50% thread | 1.8 mm | 0.0709 in | Hard or tough materials: easier tapping, fewer broken taps |
No 1.6 mm bit to hand? The closest standard bits to 1.6 mm are 1/16" (1.588 mm, fractional inch) and #52 (1.613 mm, number gauge). A slightly larger bit cuts a shallower thread; a smaller one makes the tap work harder.
Clearance holes for M2 screws
| Fit | Drill | Diameter (in) | Use it for |
|---|---|---|---|
| Close | 2.2 mm | 0.0866 in | Accurate location, well-aligned holes |
| Normal | 2.4 mm | 0.0945 in | General assembly |
| Loose | 2.6 mm | 0.1024 in | Several fasteners, or holes that may not line up |
M2 × 0.4 thread dimensions
| Dimension | Value |
|---|---|
| Thread series | ISO metric coarse thread |
| Major diameter | 2.0 mm |
| Pitch diameter | 1.74 mm |
| Minor diameter | 1.509 mm |
| Pitch | 0.4 mm |
| M2 set screw hex key | 0.9 mm |
Head sizes for M2 screws and bolts
| Head type | Head diameter | Head height | Across flats | Drive | Standard |
|---|---|---|---|---|---|
| Socket Head Cap Screw | 3.8 mm | 2.0 mm | n/a | hex socket 1.5 | DIN 912, ISO 4762 |
| Hex Head Bolt | n/a | 1.4 mm | 4.0 mm | external hex 4 | DIN 933, ISO 4017 (full thread), DIN 931, ISO 4014 (partial thread) |
| Pan Head Screw | 4.0 mm | 1.6 mm | n/a | Phillips PH0 | DIN 7985, ISO 7045 |
| Flat Countersunk Head Screw | 3.8 mm | 1.2 mm | n/a | Phillips PH1 | DIN 965, ISO 7046 (90 deg) |
Questions
- What size drill bit do I use for an M2 × 0.4 tap?
- Use a 1.6 mm (0.0630 in) drill for 75% thread, the usual choice. In hard or tough material, a 1.8 mm (0.0709 in) drill gives 50% thread and taps more easily.
- What is the clearance hole for an M2 screw?
- Drill 2.4 mm (0.0945 in) for a normal fit. Use 2.2 mm (0.0866 in) for a close fit, or 2.6 mm (0.1024 in) for a loose fit that forgives misaligned holes.
- What is the pitch of M2 × 0.4?
- M2 × 0.4 has a 0.4 mm pitch, measured from one thread crest to the next. It is the coarse pitch for M2.
- What size spanner and hex key fit an M2 bolt?
- An M2 hex head bolt takes a 4 mm spanner or socket. An M2 socket head cap screw takes a 1.5 mm hex key.
Every thread on this site, in your pocket.
Screw sizes, tap drills and clearance holes for the workshop, offline. About Nuts & Bolts