#2-56 UNC tap drill size and clearance hole
To tap #2-56 UNC, drill #50 (1.778 mm) for 75% thread. For a screw to pass through, drill a #41 (2.438 mm) clearance hole. #2-56 UNC is a unified coarse thread (UNC) with a 2.184 mm (0.0860 in) major diameter and a 0.454 mm pitch (56 threads per inch).
- Tap drill, 75% thread
- #50
- 1.778 mm
- Clearance hole, normal fit
- #41
- 2.438 mm
- Threads per inch
- 56
- 0.454 mm pitch
- Major diameter
- 2.184 mm
- 0.0860 in
Tap drill sizes for #2-56 UNC
| Thread engagement | Drill | Diameter (mm) | Diameter (in) | Use it for |
|---|---|---|---|---|
| 75% thread | #50 | 1.778 mm | 0.0700 in | The usual choice for most materials |
| 50% thread | #47 | 1.994 mm | 0.0785 in | Hard or tough materials: easier tapping, fewer broken taps |
No #50 bit to hand? The closest standard bits to 1.778 mm are 1.8 mm (metric) and 1/16" (1.588 mm, fractional inch). A slightly larger bit cuts a shallower thread; a smaller one makes the tap work harder.
Clearance holes for #2 screws
| Fit | Drill | Diameter (mm) | Diameter (in) | Use it for |
|---|---|---|---|---|
| Close | #43 | 2.261 mm | 0.0890 in | Accurate location, well-aligned holes |
| Normal | #41 | 2.438 mm | 0.0960 in | General assembly |
| Loose | #37 | 2.642 mm | 0.1040 in | Several fasteners, or holes that may not line up |
#2-56 UNC thread dimensions
| Dimension | Value |
|---|---|
| Thread series | Unified coarse thread (UNC) |
| Major diameter | 2.184 mm (0.0860 in) |
| Pitch diameter | 1.89 mm (0.0744 in) |
| Minor diameter | 1.628 mm (0.0641 in) |
| Pitch | 0.454 mm (0.0179 in) |
| Threads per inch | 56 |
Head sizes for #2 screws and bolts
| Head type | Head diameter | Head height | Across flats | Drive | Standard |
|---|---|---|---|---|---|
| Socket Head Cap Screw | 3.66 mm | 2.18 mm | n/a | hex socket 5/64" | ASME B18.3 |
| Hex Head Bolt | n/a | 1.65 mm | 4.76 mm | external hex 3/16" | ASME B18.2.1 |
| Pan Head Screw | 4.47 mm | 1.5 mm | n/a | Phillips PH0 | ASME B18.6.3 |
| Flat Countersunk Head Screw | 4.37 mm | 1.47 mm | n/a | Phillips PH0 | ASME B18.6.3 (82 deg) |
Questions
- What size drill bit do I use for a #2-56 UNC tap?
- Use a #50 (1.778 mm) drill for 75% thread, the usual choice. In hard or tough material, a #47 (1.994 mm) drill gives 50% thread and taps more easily.
- What is the clearance hole for a #2 screw?
- Drill #41 (2.438 mm) for a normal fit. Use #43 (2.261 mm) for a close fit, or #37 (2.642 mm) for a loose fit that forgives misaligned holes.
- How many threads per inch does #2-56 UNC have?
- 56 threads per inch, which is a pitch of 0.454 mm. It is the coarse (UNC) thread for #2; the fine thread is #2-64 UNF.
- What size spanner and hex key fit a #2 bolt?
- A #2 hex head bolt takes a 3/16" spanner or socket. A #2 socket head cap screw takes a 5/64" hex key.
Every thread on this site, in your pocket.
Screw sizes, tap drills and clearance holes for the workshop, offline. About Nuts & Bolts