M16 × 1.5 tap drill size and clearance hole
To tap M16 × 1.5, drill 14.5 mm (0.5709 in) for 75% thread. For a screw to pass through, drill a 18.0 mm (0.7087 in) clearance hole. M16 × 1.5 is an ISO metric fine thread with a 16.0 mm major diameter and a 1.5 mm pitch.
- Tap drill, 75% thread
- 14.5 mm
- 0.5709 in
- Clearance hole, normal fit
- 18.0 mm
- 0.7087 in
- Pitch
- 1.5 mm
- fine pitch
- Major diameter
- 16.0 mm
- 0.6299 in
Tap drill sizes for M16 × 1.5
| Thread engagement | Drill | Diameter (in) | Use it for |
|---|---|---|---|
| 75% thread | 14.5 mm | 0.5709 in | The usual choice for most materials |
| 50% thread | 15.25 mm | 0.6004 in | Hard or tough materials: easier tapping, fewer broken taps |
No 14.5 mm bit to hand? The closest standard bits to 14.5 mm are 37/64" (14.684 mm, fractional inch). A slightly larger bit cuts a shallower thread; a smaller one makes the tap work harder.
Clearance holes for M16 screws
| Fit | Drill | Diameter (in) | Use it for |
|---|---|---|---|
| Close | 17.0 mm | 0.6693 in | Accurate location, well-aligned holes |
| Normal | 18.0 mm | 0.7087 in | General assembly |
| Loose | 19.0 mm | 0.7480 in | Several fasteners, or holes that may not line up |
M16 × 1.5 thread dimensions
| Dimension | Value |
|---|---|
| Thread series | ISO metric fine thread |
| Major diameter | 16.0 mm |
| Pitch diameter | 15.026 mm |
| Minor diameter | 14.16 mm |
| Pitch | 1.5 mm |
Head sizes for M16 screws and bolts
| Head type | Head diameter | Head height | Across flats | Drive | Standard |
|---|---|---|---|---|---|
| Socket Head Cap Screw | 24.0 mm | 16.0 mm | n/a | hex socket 14.0 | DIN 912, ISO 4762 |
| Hex Head Bolt | n/a | 10.0 mm | 24.0 mm | external hex 24 | DIN 933, ISO 4017 (full thread), DIN 931, ISO 4014 (partial thread) |
| Pan Head Screw | 32.0 mm | 9.0 mm | n/a | Phillips PH4 | DIN 7985, ISO 7045 |
| Flat Countersunk Head Screw | 29.0 mm | 8.0 mm | n/a | Phillips PH4 | DIN 965, ISO 7046 (90 deg) |
Questions
- What size drill bit do I use for an M16 × 1.5 tap?
- Use a 14.5 mm (0.5709 in) drill for 75% thread, the usual choice. In hard or tough material, a 15.25 mm (0.6004 in) drill gives 50% thread and taps more easily.
- What is the clearance hole for an M16 screw?
- Drill 18.0 mm (0.7087 in) for a normal fit. Use 17.0 mm (0.6693 in) for a close fit, or 19.0 mm (0.7480 in) for a loose fit that forgives misaligned holes.
- What is the pitch of M16 × 1.5?
- M16 × 1.5 has a 1.5 mm pitch, measured from one thread crest to the next. It is the fine pitch for M16; the coarse pitch is M16 × 2.0.
- What size spanner and hex key fit an M16 bolt?
- An M16 hex head bolt takes a 24 mm spanner or socket. An M16 socket head cap screw takes a 14.0 mm hex key.
Every thread on this site, in your pocket.
Screw sizes, tap drills and clearance holes for the workshop, offline. About Nuts & Bolts