Skip to content

M14 × 1.5 tap drill size and clearance hole

To tap M14 × 1.5, drill 12.5 mm (0.4921 in) for 75% thread. For a screw to pass through, drill a 15.5 mm (0.6102 in) clearance hole. M14 × 1.5 is an ISO metric fine thread with a 14.0 mm major diameter and a 1.5 mm pitch.

Tap drill, 75% thread
12.5 mm
0.4921 in
Clearance hole, normal fit
15.5 mm
0.6102 in
Pitch
1.5 mm
fine pitch
Major diameter
14.0 mm
0.5512 in

Tap drill sizes for M14 × 1.5

Tap drill sizes for M14 × 1.5
Thread engagementDrillDiameter (in)Use it for
75% thread12.5 mm0.4921 inThe usual choice for most materials
50% thread13.25 mm0.5217 inHard or tough materials: easier tapping, fewer broken taps

No 12.5 mm bit to hand? The closest standard bits to 12.5 mm are 31/64" (12.303 mm, fractional inch). A slightly larger bit cuts a shallower thread; a smaller one makes the tap work harder.

Clearance holes for M14 screws

Clearance hole sizes for M14 screws
FitDrillDiameter (in)Use it for
Close15.0 mm0.5906 inAccurate location, well-aligned holes
Normal15.5 mm0.6102 inGeneral assembly
Loose17.0 mm0.6693 inSeveral fasteners, or holes that may not line up

M14 × 1.5 thread dimensions

M14 × 1.5 thread dimensions
DimensionValue
Thread seriesISO metric fine thread
Major diameter14.0 mm
Pitch diameter13.026 mm
Minor diameter12.16 mm
Pitch1.5 mm

Head sizes for M14 screws and bolts

Head dimensions for M14 screws and bolts
Head typeHead diameterHead heightAcross flatsDriveStandard
Socket Head Cap Screw21.0 mm14.0 mmn/ahex socket 12.0DIN 912, ISO 4762
Hex Head Boltn/a8.8 mm21.0 mmexternal hex 21DIN 933, ISO 4017 (full thread), DIN 931, ISO 4014 (partial thread)
Pan Head Screw28.0 mm8.0 mmn/aPhillips PH4DIN 7985, ISO 7045
Flat Countersunk Head Screw25.0 mm7.0 mmn/aPhillips PH4DIN 965, ISO 7046 (90 deg)

Questions

What size drill bit do I use for an M14 × 1.5 tap?
Use a 12.5 mm (0.4921 in) drill for 75% thread, the usual choice. In hard or tough material, a 13.25 mm (0.5217 in) drill gives 50% thread and taps more easily.
What is the clearance hole for an M14 screw?
Drill 15.5 mm (0.6102 in) for a normal fit. Use 15.0 mm (0.5906 in) for a close fit, or 17.0 mm (0.6693 in) for a loose fit that forgives misaligned holes.
What is the pitch of M14 × 1.5?
M14 × 1.5 has a 1.5 mm pitch, measured from one thread crest to the next. It is the fine pitch for M14; the coarse pitch is M14 × 2.0.
What size spanner and hex key fit an M14 bolt?
An M14 hex head bolt takes a 21 mm spanner or socket. An M14 socket head cap screw takes a 12.0 mm hex key.

Every thread on this site, in your pocket.

Screw sizes, tap drills and clearance holes for the workshop, offline. About Nuts & Bolts

Get Nuts & Bolts on Google Play