M18 × 2.0 tap drill size and clearance hole
To tap M18 × 2.0, drill 16.0 mm (0.6299 in) for 75% thread. For a screw to pass through, drill a 20.0 mm (0.7874 in) clearance hole. M18 × 2.0 is an ISO metric fine thread with a 18.0 mm major diameter and a 2.0 mm pitch.
- Tap drill, 75% thread
- 16.0 mm
- 0.6299 in
- Clearance hole, normal fit
- 20.0 mm
- 0.7874 in
- Pitch
- 2.0 mm
- fine pitch
- Major diameter
- 18.0 mm
- 0.7087 in
Tap drill sizes for M18 × 2.0
| Thread engagement | Drill | Diameter (in) | Use it for |
|---|---|---|---|
| 75% thread | 16.0 mm | 0.6299 in | The usual choice for most materials |
| 50% thread | 17.0 mm | 0.6693 in | Hard or tough materials: easier tapping, fewer broken taps |
No 16.0 mm bit to hand? The closest standard bits to 16.0 mm are 5/8" (15.875 mm, fractional inch). A slightly larger bit cuts a shallower thread; a smaller one makes the tap work harder.
Clearance holes for M18 screws
| Fit | Drill | Diameter (in) | Use it for |
|---|---|---|---|
| Close | 19.0 mm | 0.7480 in | Accurate location, well-aligned holes |
| Normal | 20.0 mm | 0.7874 in | General assembly |
| Loose | 21.0 mm | 0.8268 in | Several fasteners, or holes that may not line up |
M18 × 2.0 thread dimensions
| Dimension | Value |
|---|---|
| Thread series | ISO metric fine thread |
| Major diameter | 18.0 mm |
| Pitch diameter | 16.701 mm |
| Minor diameter | 15.546 mm |
| Pitch | 2.0 mm |
Head sizes for M18 screws and bolts
| Head type | Head diameter | Head height | Across flats | Drive | Standard |
|---|---|---|---|---|---|
| Socket Head Cap Screw | 27.0 mm | 18.0 mm | n/a | hex socket 14.0 | DIN 912, ISO 4762 |
| Hex Head Bolt | n/a | 11.5 mm | 27.0 mm | external hex 27 | DIN 933, ISO 4017 (full thread), DIN 931, ISO 4014 (partial thread) |
Questions
- What size drill bit do I use for an M18 × 2.0 tap?
- Use a 16.0 mm (0.6299 in) drill for 75% thread, the usual choice. In hard or tough material, a 17.0 mm (0.6693 in) drill gives 50% thread and taps more easily.
- What is the clearance hole for an M18 screw?
- Drill 20.0 mm (0.7874 in) for a normal fit. Use 19.0 mm (0.7480 in) for a close fit, or 21.0 mm (0.8268 in) for a loose fit that forgives misaligned holes.
- What is the pitch of M18 × 2.0?
- M18 × 2.0 has a 2.0 mm pitch, measured from one thread crest to the next. It is the fine pitch for M18; the coarse pitch is M18 × 2.5.
- What size spanner and hex key fit an M18 bolt?
- An M18 hex head bolt takes a 27 mm spanner or socket. An M18 socket head cap screw takes a 14.0 mm hex key.
Every thread on this site, in your pocket.
Screw sizes, tap drills and clearance holes for the workshop, offline. About Nuts & Bolts