M14 × 2.0 tap drill size and clearance hole
To tap M14 × 2.0, drill 12.0 mm (0.4724 in) for 75% thread. For a screw to pass through, drill a 15.5 mm (0.6102 in) clearance hole. M14 × 2.0 is an ISO metric coarse thread with a 14.0 mm major diameter and a 2.0 mm pitch.
- Tap drill, 75% thread
- 12.0 mm
- 0.4724 in
- Clearance hole, normal fit
- 15.5 mm
- 0.6102 in
- Pitch
- 2.0 mm
- coarse pitch
- Major diameter
- 14.0 mm
- 0.5512 in
Tap drill sizes for M14 × 2.0
| Thread engagement | Drill | Diameter (in) | Use it for |
|---|---|---|---|
| 75% thread | 12.0 mm | 0.4724 in | The usual choice for most materials |
| 50% thread | 13.0 mm | 0.5118 in | Hard or tough materials: easier tapping, fewer broken taps |
No 12.0 mm bit to hand? The closest standard bits to 12.0 mm are 15/32" (11.906 mm, fractional inch). A slightly larger bit cuts a shallower thread; a smaller one makes the tap work harder.
Clearance holes for M14 screws
| Fit | Drill | Diameter (in) | Use it for |
|---|---|---|---|
| Close | 15.0 mm | 0.5906 in | Accurate location, well-aligned holes |
| Normal | 15.5 mm | 0.6102 in | General assembly |
| Loose | 17.0 mm | 0.6693 in | Several fasteners, or holes that may not line up |
M14 × 2.0 thread dimensions
| Dimension | Value |
|---|---|
| Thread series | ISO metric coarse thread |
| Major diameter | 14.0 mm |
| Pitch diameter | 12.701 mm |
| Minor diameter | 11.546 mm |
| Pitch | 2.0 mm |
| M14 set screw hex key | 6.0 mm |
Head sizes for M14 screws and bolts
| Head type | Head diameter | Head height | Across flats | Drive | Standard |
|---|---|---|---|---|---|
| Socket Head Cap Screw | 21.0 mm | 14.0 mm | n/a | hex socket 12.0 | DIN 912, ISO 4762 |
| Hex Head Bolt | n/a | 8.8 mm | 21.0 mm | external hex 21 | DIN 933, ISO 4017 (full thread), DIN 931, ISO 4014 (partial thread) |
| Pan Head Screw | 28.0 mm | 8.0 mm | n/a | Phillips PH4 | DIN 7985, ISO 7045 |
| Flat Countersunk Head Screw | 25.0 mm | 7.0 mm | n/a | Phillips PH4 | DIN 965, ISO 7046 (90 deg) |
Questions
- What size drill bit do I use for an M14 × 2.0 tap?
- Use a 12.0 mm (0.4724 in) drill for 75% thread, the usual choice. In hard or tough material, a 13.0 mm (0.5118 in) drill gives 50% thread and taps more easily.
- What is the clearance hole for an M14 screw?
- Drill 15.5 mm (0.6102 in) for a normal fit. Use 15.0 mm (0.5906 in) for a close fit, or 17.0 mm (0.6693 in) for a loose fit that forgives misaligned holes.
- What is the pitch of M14 × 2.0?
- M14 × 2.0 has a 2.0 mm pitch, measured from one thread crest to the next. It is the coarse pitch for M14; the fine pitch is M14 × 1.5.
- What size spanner and hex key fit an M14 bolt?
- An M14 hex head bolt takes a 21 mm spanner or socket. An M14 socket head cap screw takes a 12.0 mm hex key.
Every thread on this site, in your pocket.
Screw sizes, tap drills and clearance holes for the workshop, offline. About Nuts & Bolts