M12 × 1.75 tap drill size and clearance hole
To tap M12 × 1.75, drill 10.2 mm (0.4016 in) for 75% thread. For a screw to pass through, drill a 14.0 mm (0.5512 in) clearance hole. M12 × 1.75 is an ISO metric coarse thread with a 12.0 mm major diameter and a 1.75 mm pitch.
- Tap drill, 75% thread
- 10.2 mm
- 0.4016 in
- Clearance hole, normal fit
- 14.0 mm
- 0.5512 in
- Pitch
- 1.75 mm
- coarse pitch
- Major diameter
- 12.0 mm
- 0.4724 in
Tap drill sizes for M12 × 1.75
| Thread engagement | Drill | Diameter (in) | Use it for |
|---|---|---|---|
| 75% thread | 10.2 mm | 0.4016 in | The usual choice for most materials |
| 50% thread | 11.0 mm | 0.4380 in | Hard or tough materials: easier tapping, fewer broken taps |
No 10.2 mm bit to hand? The closest standard bits to 10.2 mm are Letter Y (10.262 mm, letter gauge), 13/32" (10.319 mm, fractional inch) and 10.0 mm (metric). A slightly larger bit cuts a shallower thread; a smaller one makes the tap work harder.
Clearance holes for M12 screws
| Fit | Drill | Diameter (in) | Use it for |
|---|---|---|---|
| Close | 13.0 mm | 0.5118 in | Accurate location, well-aligned holes |
| Normal | 14.0 mm | 0.5512 in | General assembly |
| Loose | 15.0 mm | 0.5906 in | Several fasteners, or holes that may not line up |
M12 × 1.75 thread dimensions
| Dimension | Value |
|---|---|
| Thread series | ISO metric coarse thread |
| Major diameter | 12.0 mm |
| Pitch diameter | 10.863 mm |
| Minor diameter | 9.853 mm |
| Pitch | 1.75 mm |
| M12 set screw hex key | 6.0 mm |
Head sizes for M12 screws and bolts
| Head type | Head diameter | Head height | Across flats | Drive | Standard |
|---|---|---|---|---|---|
| Socket Head Cap Screw | 18.0 mm | 12.0 mm | n/a | hex socket 10.0 | DIN 912, ISO 4762 |
| Hex Head Bolt | n/a | 7.5 mm | 18.0 mm | external hex 18 | DIN 933, ISO 4017 (full thread), DIN 931, ISO 4014 (partial thread) |
| Pan Head Screw | 24.0 mm | 7.0 mm | n/a | Phillips PH4 | DIN 7985, ISO 7045 |
| Flat Countersunk Head Screw | 22.0 mm | 6.0 mm | n/a | Phillips PH4 | DIN 965, ISO 7046 (90 deg) |
Questions
- What size drill bit do I use for an M12 × 1.75 tap?
- Use a 10.2 mm (0.4016 in) drill for 75% thread, the usual choice. In hard or tough material, a 11.0 mm (0.4380 in) drill gives 50% thread and taps more easily.
- What is the clearance hole for an M12 screw?
- Drill 14.0 mm (0.5512 in) for a normal fit. Use 13.0 mm (0.5118 in) for a close fit, or 15.0 mm (0.5906 in) for a loose fit that forgives misaligned holes.
- What is the pitch of M12 × 1.75?
- M12 × 1.75 has a 1.75 mm pitch, measured from one thread crest to the next. It is the coarse pitch for M12; the fine pitch is M12 × 1.5.
- What size spanner and hex key fit an M12 bolt?
- An M12 hex head bolt takes a 18 mm spanner or socket. An M12 socket head cap screw takes a 10.0 mm hex key.
Every thread on this site, in your pocket.
Screw sizes, tap drills and clearance holes for the workshop, offline. About Nuts & Bolts