Skip to content

M10 × 1.5 tap drill size and clearance hole

To tap M10 × 1.5, drill 8.5 mm (0.3346 in) for 75% thread. For a screw to pass through, drill a 11.0 mm (0.4331 in) clearance hole. M10 × 1.5 is an ISO metric coarse thread with a 10.0 mm major diameter and a 1.5 mm pitch.

Tap drill, 75% thread
8.5 mm
0.3346 in
Clearance hole, normal fit
11.0 mm
0.4331 in
Pitch
1.5 mm
coarse pitch
Major diameter
10.0 mm
0.3937 in

Tap drill sizes for M10 × 1.5

Tap drill sizes for M10 × 1.5
Thread engagementDrillDiameter (in)Use it for
75% thread8.5 mm0.3346 inThe usual choice for most materials
50% thread9.25 mm0.3642 inHard or tough materials: easier tapping, fewer broken taps

No 8.5 mm bit to hand? The closest standard bits to 8.5 mm are Letter Q (8.433 mm, letter gauge) and 21/64" (8.334 mm, fractional inch). A slightly larger bit cuts a shallower thread; a smaller one makes the tap work harder.

Clearance holes for M10 screws

Clearance hole sizes for M10 screws
FitDrillDiameter (in)Use it for
Close10.5 mm0.4134 inAccurate location, well-aligned holes
Normal11.0 mm0.4331 inGeneral assembly
Loose12.0 mm0.4724 inSeveral fasteners, or holes that may not line up

M10 × 1.5 thread dimensions

M10 × 1.5 thread dimensions
DimensionValue
Thread seriesISO metric coarse thread
Major diameter10.0 mm
Pitch diameter9.026 mm
Minor diameter8.16 mm
Pitch1.5 mm
M10 set screw hex key5.0 mm

Head sizes for M10 screws and bolts

Head dimensions for M10 screws and bolts
Head typeHead diameterHead heightAcross flatsDriveStandard
Socket Head Cap Screw16.0 mm10.0 mmn/ahex socket 8.0DIN 912, ISO 4762
Hex Head Boltn/a6.4 mm16.0 mmexternal hex 16DIN 933, ISO 4017 (full thread), DIN 931, ISO 4014 (partial thread)
Pan Head Screw20.0 mm7.5 mmn/aPhillips PH4DIN 7985, ISO 7045
Flat Countersunk Head Screw18.0 mm5.0 mmn/aPhillips PH4DIN 965, ISO 7046 (90 deg)

Questions

What size drill bit do I use for an M10 × 1.5 tap?
Use a 8.5 mm (0.3346 in) drill for 75% thread, the usual choice. In hard or tough material, a 9.25 mm (0.3642 in) drill gives 50% thread and taps more easily.
What is the clearance hole for an M10 screw?
Drill 11.0 mm (0.4331 in) for a normal fit. Use 10.5 mm (0.4134 in) for a close fit, or 12.0 mm (0.4724 in) for a loose fit that forgives misaligned holes.
What is the pitch of M10 × 1.5?
M10 × 1.5 has a 1.5 mm pitch, measured from one thread crest to the next. It is the coarse pitch for M10; the fine pitch is M10 × 1.25.
What size spanner and hex key fit an M10 bolt?
An M10 hex head bolt takes a 16 mm spanner or socket. An M10 socket head cap screw takes a 8.0 mm hex key.

Every thread on this site, in your pocket.

Screw sizes, tap drills and clearance holes for the workshop, offline. About Nuts & Bolts

Get Nuts & Bolts on Google Play