M10 × 1.25 tap drill size and clearance hole
To tap M10 × 1.25, drill 8.8 mm (0.3445 in) for 75% thread. For a screw to pass through, drill a 11.0 mm (0.4331 in) clearance hole. M10 × 1.25 is an ISO metric fine thread with a 10.0 mm major diameter and a 1.25 mm pitch.
- Tap drill, 75% thread
- 8.8 mm
- 0.3445 in
- Clearance hole, normal fit
- 11.0 mm
- 0.4331 in
- Pitch
- 1.25 mm
- fine pitch
- Major diameter
- 10.0 mm
- 0.3937 in
Tap drill sizes for M10 × 1.25
| Thread engagement | Drill | Diameter (in) | Use it for |
|---|---|---|---|
| 75% thread | 8.8 mm | 0.3445 in | The usual choice for most materials |
| 50% thread | 9.4 mm | 0.3691 in | Hard or tough materials: easier tapping, fewer broken taps |
No 8.8 mm bit to hand? The closest standard bits to 8.75 mm are 11/32" (8.731 mm, fractional inch) and Letter S (8.839 mm, letter gauge). A slightly larger bit cuts a shallower thread; a smaller one makes the tap work harder.
Clearance holes for M10 screws
| Fit | Drill | Diameter (in) | Use it for |
|---|---|---|---|
| Close | 10.5 mm | 0.4134 in | Accurate location, well-aligned holes |
| Normal | 11.0 mm | 0.4331 in | General assembly |
| Loose | 12.0 mm | 0.4724 in | Several fasteners, or holes that may not line up |
M10 × 1.25 thread dimensions
| Dimension | Value |
|---|---|
| Thread series | ISO metric fine thread |
| Major diameter | 10.0 mm |
| Pitch diameter | 9.188 mm |
| Minor diameter | 8.466 mm |
| Pitch | 1.25 mm |
Head sizes for M10 screws and bolts
| Head type | Head diameter | Head height | Across flats | Drive | Standard |
|---|---|---|---|---|---|
| Socket Head Cap Screw | 16.0 mm | 10.0 mm | n/a | hex socket 8.0 | DIN 912, ISO 4762 |
| Hex Head Bolt | n/a | 6.4 mm | 16.0 mm | external hex 16 | DIN 933, ISO 4017 (full thread), DIN 931, ISO 4014 (partial thread) |
| Pan Head Screw | 20.0 mm | 7.5 mm | n/a | Phillips PH4 | DIN 7985, ISO 7045 |
| Flat Countersunk Head Screw | 18.0 mm | 5.0 mm | n/a | Phillips PH4 | DIN 965, ISO 7046 (90 deg) |
Questions
- What size drill bit do I use for an M10 × 1.25 tap?
- Use a 8.8 mm (0.3445 in) drill for 75% thread, the usual choice. In hard or tough material, a 9.4 mm (0.3691 in) drill gives 50% thread and taps more easily.
- What is the clearance hole for an M10 screw?
- Drill 11.0 mm (0.4331 in) for a normal fit. Use 10.5 mm (0.4134 in) for a close fit, or 12.0 mm (0.4724 in) for a loose fit that forgives misaligned holes.
- What is the pitch of M10 × 1.25?
- M10 × 1.25 has a 1.25 mm pitch, measured from one thread crest to the next. It is the fine pitch for M10; the coarse pitch is M10 × 1.5.
- What size spanner and hex key fit an M10 bolt?
- An M10 hex head bolt takes a 16 mm spanner or socket. An M10 socket head cap screw takes a 8.0 mm hex key.
Every thread on this site, in your pocket.
Screw sizes, tap drills and clearance holes for the workshop, offline. About Nuts & Bolts