Skip to content

M8 × 1.0 tap drill size and clearance hole

To tap M8 × 1.0, drill 7.0 mm (0.2756 in) for 75% thread. For a screw to pass through, drill a 9.0 mm (0.3543 in) clearance hole. M8 × 1.0 is an ISO metric fine thread with a 8.0 mm major diameter and a 1.0 mm pitch.

Tap drill, 75% thread
7.0 mm
0.2756 in
Clearance hole, normal fit
9.0 mm
0.3543 in
Pitch
1.0 mm
fine pitch
Major diameter
8.0 mm
0.3150 in

Tap drill sizes for M8 × 1.0

Tap drill sizes for M8 × 1.0
Thread engagementDrillDiameter (in)Use it for
75% thread7.0 mm0.2756 inThe usual choice for most materials
50% thread7.5 mm0.2953 inHard or tough materials: easier tapping, fewer broken taps

No 7.0 mm bit to hand? The closest standard bits to 7.0 mm are Letter J (7.036 mm, letter gauge) and 9/32" (7.144 mm, fractional inch). A slightly larger bit cuts a shallower thread; a smaller one makes the tap work harder.

Clearance holes for M8 screws

Clearance hole sizes for M8 screws
FitDrillDiameter (in)Use it for
Close8.4 mm0.3307 inAccurate location, well-aligned holes
Normal9.0 mm0.3543 inGeneral assembly
Loose10.0 mm0.3937 inSeveral fasteners, or holes that may not line up

M8 × 1.0 thread dimensions

M8 × 1.0 thread dimensions
DimensionValue
Thread seriesISO metric fine thread
Major diameter8.0 mm
Pitch diameter7.35 mm
Minor diameter6.773 mm
Pitch1.0 mm

Head sizes for M8 screws and bolts

Head dimensions for M8 screws and bolts
Head typeHead diameterHead heightAcross flatsDriveStandard
Socket Head Cap Screw13.0 mm8.0 mmn/ahex socket 6.0DIN 912, ISO 4762
Hex Head Boltn/a5.3 mm13.0 mmexternal hex 13DIN 933, ISO 4017 (full thread), DIN 931, ISO 4014 (partial thread)
Pan Head Screw16.0 mm6.0 mmn/aPhillips PH4DIN 7985, ISO 7045
Flat Countersunk Head Screw14.5 mm4.0 mmn/aPhillips PH4DIN 965, ISO 7046 (90 deg)

Questions

What size drill bit do I use for an M8 × 1.0 tap?
Use a 7.0 mm (0.2756 in) drill for 75% thread, the usual choice. In hard or tough material, a 7.5 mm (0.2953 in) drill gives 50% thread and taps more easily.
What is the clearance hole for an M8 screw?
Drill 9.0 mm (0.3543 in) for a normal fit. Use 8.4 mm (0.3307 in) for a close fit, or 10.0 mm (0.3937 in) for a loose fit that forgives misaligned holes.
What is the pitch of M8 × 1.0?
M8 × 1.0 has a 1.0 mm pitch, measured from one thread crest to the next. It is the fine pitch for M8; the coarse pitch is M8 × 1.25.
What size spanner and hex key fit an M8 bolt?
An M8 hex head bolt takes a 13 mm spanner or socket. An M8 socket head cap screw takes a 6.0 mm hex key.

Every thread on this site, in your pocket.

Screw sizes, tap drills and clearance holes for the workshop, offline. About Nuts & Bolts

Get Nuts & Bolts on Google Play