M20 × 2.5 tap drill size and clearance hole
To tap M20 × 2.5, drill 17.5 mm (0.6890 in) for 75% thread. For a screw to pass through, drill a 22.0 mm (0.8661 in) clearance hole. M20 × 2.5 is an ISO metric coarse thread with a 20.0 mm major diameter and a 2.5 mm pitch.
- Tap drill, 75% thread
- 17.5 mm
- 0.6890 in
- Clearance hole, normal fit
- 22.0 mm
- 0.8661 in
- Pitch
- 2.5 mm
- coarse pitch
- Major diameter
- 20.0 mm
- 0.7874 in
Tap drill sizes for M20 × 2.5
| Thread engagement | Drill | Diameter (in) | Use it for |
|---|---|---|---|
| 75% thread | 17.5 mm | 0.6890 in | The usual choice for most materials |
| 50% thread | 18.75 mm | 0.7382 in | Hard or tough materials: easier tapping, fewer broken taps |
No 17.5 mm bit to hand? The closest standard bits to 17.5 mm are 11/16" (17.463 mm, fractional inch). A slightly larger bit cuts a shallower thread; a smaller one makes the tap work harder.
Clearance holes for M20 screws
| Fit | Drill | Diameter (in) | Use it for |
|---|---|---|---|
| Close | 21.0 mm | 0.8268 in | Accurate location, well-aligned holes |
| Normal | 22.0 mm | 0.8661 in | General assembly |
| Loose | 24.0 mm | 0.9449 in | Several fasteners, or holes that may not line up |
M20 × 2.5 thread dimensions
| Dimension | Value |
|---|---|
| Thread series | ISO metric coarse thread |
| Major diameter | 20.0 mm |
| Pitch diameter | 18.376 mm |
| Minor diameter | 16.933 mm |
| Pitch | 2.5 mm |
| M20 set screw hex key | 10.0 mm |
Head sizes for M20 screws and bolts
| Head type | Head diameter | Head height | Across flats | Drive | Standard |
|---|---|---|---|---|---|
| Socket Head Cap Screw | 30.0 mm | 20.0 mm | n/a | hex socket 17.0 | DIN 912, ISO 4762 |
| Hex Head Bolt | n/a | 12.5 mm | 30.0 mm | external hex 30 | DIN 933, ISO 4017 (full thread), DIN 931, ISO 4014 (partial thread) |
Questions
- What size drill bit do I use for an M20 × 2.5 tap?
- Use a 17.5 mm (0.6890 in) drill for 75% thread, the usual choice. In hard or tough material, a 18.75 mm (0.7382 in) drill gives 50% thread and taps more easily.
- What is the clearance hole for an M20 screw?
- Drill 22.0 mm (0.8661 in) for a normal fit. Use 21.0 mm (0.8268 in) for a close fit, or 24.0 mm (0.9449 in) for a loose fit that forgives misaligned holes.
- What is the pitch of M20 × 2.5?
- M20 × 2.5 has a 2.5 mm pitch, measured from one thread crest to the next. It is the coarse pitch for M20; the fine pitch is M20 × 2.0.
- What size spanner and hex key fit an M20 bolt?
- An M20 hex head bolt takes a 30 mm spanner or socket. An M20 socket head cap screw takes a 17.0 mm hex key.
Every thread on this site, in your pocket.
Screw sizes, tap drills and clearance holes for the workshop, offline. About Nuts & Bolts