7/16"-20 UNF tap drill size and clearance hole
To tap 7/16"-20 UNF, drill 25/64" (9.922 mm) for 75% thread. For a screw to pass through, drill a 31/64" (12.303 mm) clearance hole. 7/16"-20 UNF is a unified fine thread (UNF) with a 11.113 mm (0.4375 in) major diameter and a 1.27 mm pitch (20 threads per inch).
- Tap drill, 75% thread
- 25/64"
- 9.922 mm
- Clearance hole, normal fit
- 31/64"
- 12.303 mm
- Threads per inch
- 20
- 1.27 mm pitch
- Major diameter
- 11.113 mm
- 0.4375 in
Tap drill sizes for 7/16"-20 UNF
| Thread engagement | Drill | Diameter (mm) | Diameter (in) | Use it for |
|---|---|---|---|---|
| 75% thread | 25/64" | 9.922 mm | 0.3906 in | The usual choice for most materials |
| 50% thread | letter Z | 10.49 mm | 0.4130 in | Hard or tough materials: easier tapping, fewer broken taps |
No 25/64" bit to hand? The closest standard bits to 9.922 mm are 10.0 mm (metric) and Letter W (9.804 mm, letter gauge). A slightly larger bit cuts a shallower thread; a smaller one makes the tap work harder.
Clearance holes for 7/16" screws
| Fit | Drill | Diameter (mm) | Diameter (in) | Use it for |
|---|---|---|---|---|
| Close | 15/32" | 11.906 mm | 0.4687 in | Accurate location, well-aligned holes |
| Normal | 31/64" | 12.303 mm | 0.4844 in | General assembly |
| Loose | 33/64" | 13.097 mm | 0.5156 in | Several fasteners, or holes that may not line up |
7/16"-20 UNF thread dimensions
| Dimension | Value |
|---|---|
| Thread series | Unified fine thread (UNF) |
| Major diameter | 11.113 mm (0.4375 in) |
| Pitch diameter | 10.287 mm (0.4050 in) |
| Minor diameter | 9.55 mm (0.3760 in) |
| Pitch | 1.27 mm (0.0500 in) |
| Threads per inch | 20 |
Head sizes for 7/16" screws and bolts
| Head type | Head diameter | Head height | Across flats | Drive | Standard |
|---|---|---|---|---|---|
| Socket Head Cap Screw | 16.66 mm | 11.11 mm | n/a | hex socket 3/8" | ASME B18.3 |
| Hex Head Bolt | n/a | 7.95 mm | 17.46 mm | external hex 11/16" | ASME B18.2.1 |
| Pan Head Screw | 21.54 mm | 7.11 mm | n/a | Phillips PH4 | ASME B18.6.3 |
| Flat Countersunk Head Screw | 22.23 mm | 6.73 mm | n/a | Phillips PH4 | ASME B18.6.3 (82 deg) |
Questions
- What size drill bit do I use for a 7/16"-20 UNF tap?
- Use a 25/64" (9.922 mm) drill for 75% thread, the usual choice. In hard or tough material, a letter Z (10.49 mm) drill gives 50% thread and taps more easily.
- What is the clearance hole for a 7/16" screw?
- Drill 31/64" (12.303 mm) for a normal fit. Use 15/32" (11.906 mm) for a close fit, or 33/64" (13.097 mm) for a loose fit that forgives misaligned holes.
- How many threads per inch does 7/16"-20 UNF have?
- 20 threads per inch, which is a pitch of 1.27 mm. It is the fine (UNF) thread for 7/16"; the coarse thread is 7/16"-14 UNC.
- What size spanner and hex key fit a 7/16" bolt?
- A 7/16" hex head bolt takes a 11/16" spanner or socket. A 7/16" socket head cap screw takes a 3/8" hex key.
Every thread on this site, in your pocket.
Screw sizes, tap drills and clearance holes for the workshop, offline. About Nuts & Bolts